Cincoze CS-100/P2000 Series User Manual Download

Page: 40 / 116

100/

P2000 Series | User Manual

1.6.2 Rear

CFast and SIM Card

CFast card and SIM card slot

HDD/SSD

2.5” SATA HDD/SSD Bay, Support RAID 0/1

Power On/Off Switch

Power-on or power-off the system

1.6.3 Side (Left)

Antenna Hole

Used to connect an antenna for optional
Mini-PCIe WiFi module

Universal I/O Bracket

Used to expand I/O for Mini-PCIe module

AT/ATX Switch

Used to select AT or ATX power mode

Reset Button

Used to reset the system

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard disk drive

OSD Function

(For CDS Display Module)

- LCD On/Off

Press to turn-on or turn-off the backlight of display

Increase Brightness

Press to increase brightness of the screen

- Decrease Brightness

Press to decrease brightness of the screen

Summary of Contents for CS-100/P2000 Series





















































































































Search results

Summary of Contents for CS-100/P2000 Series

Reviews:

Related manuals for CS-100/P2000 Series

Brands by name

Popular brands

Cincoze CS-100/P2000 Series, User Manual

Search results

Summary of Contents for CS-100/P2000 Series

Reviews:

Related manuals for CS-100/P2000 Series

Brands by name

Popular brands