manualshive.com logo in svg

Chroma 19032-P, Quick Start Manual

Share
Download
Chroma 19032-P Quick Start Manual Download Page 32

Electrical Safety Analyzer 19032-P Quick Start Guide 

 

Option (6000-03): 8 points of HV 
output. (UL approval) 

Option (6000-04): HV / LC 
scanner 

Option (6000-05): HV / LC 
scanner with probe 
Option (6000-06): L-N Scanner 
& Leakage Current Scanner 
Option (6000-07): HV / LC   
scanner with probe 20A 
Option (6000-08): HV / LC / LAC 
/ LDC probe scanner 20A 
Option (6000-11): 4 points of HV 

Figure 4-3

 

)  REMOTE I/O : 

The test result signal input/output terminal.   

CK: 

ed when the two 

UNDER TEST: 

st status, this output 

 by 

   

 

PASS: When th

nt is 

        FAIL: When the analyzer judges DUT as fail, this output terminal will   

t 

EOS:

output & 4 sets of grounding 
terminals 

   

(9

START: 

Start test signal input terminal. 

RESET: 

Stop test signal input terminal. 

INTER LO

The high voltage can be outputt
terminals are short-circuited. 
When the analyzer is under te
terminal will short circuit.    Control external signal is
using this short condition.    The junction specification 
125V AC current is lower than 1A action time.    This 
analyzer is under testing status until STOP is stopped. 

e analyzer judges DUT as pass, this output terminal will   

short circuit.    Control external signal is by using this short 
circuit condition.    The junction specification 125V AC curre
lower than 1A.    The action time is from judged as pass to be 
stopped. 

short circuit.  Control external signal is by using this short circui
condition.    The junction specification 125V AC current is lower 
than 1A.    The action time is from judged as fail to be stopped. 

 When the tester is performing the test in test step, the output   

terminal will be short-circuited.    By using this short-circuited   
condition to control external signal.    The connection point   

18 

Summary of Contents for 19032-P
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands