manualshive.com logo in svg

Christie Spyder X20, User Manual

Share
Download
Christie Spyder X20 User Manual Download Page 140

 

 

Spyder X20 Hardware Family 

Spyder X20 User Manual 

140 

020-000916-01 Rev. 1 (04-2016) 

Spyder X20 Hardware Family 

Spyder X20 is a second generation Spyder hardware line.  X20 increases both the I/O capacity and virtual image 
space (VI) available within a single chassis, making a powerful and cost-effective solution for mid-range Spyder 
configurations. 

Spyder X20 Models 

Spyder X20 uses a modular chassis design, which can be populated at the factory with various combinations of 
input and output channels as required.  Available chassis sizes start at three-slot configurations. 

Note that not all slots must be filled in a chassis; a larger chassis will operate without all slots being filled.  This 
makes an easy hardware upgrade path for systems that may need to increase capacity over time. 

Spyder X20 External Connections 

The connections for the Spyder X20’s internal computer are exposed on the back panel.  These connections are 

for factory use only, and are not intended to be connected to external peripherals (keyboard / mouse / monitor) 
by a user.  Specifically, the following connections are exposed: 

Keyboard 

Mouse 

Monitor (HD15) 

USB 

Microphone Input 

Speaker Outputs 

Summary of Contents for Spyder X20













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands