Chiltrix CX34 Installation And Operation Manual Download Page 50

Page: 50 / 61

Chiltrix Inc.

www.chiltrix.com

5 STATUS

The status application is used to check the detailed status of the unit operation, such as
compressor speed, fan speed, G1, G2, G3, G4 valves and so on. See Fig. 5-1

5.1 State preview display interface

Compressor:

Displays the current working status of the compressor.

Compressor Heating:

Displays compressor heating status.

Outdoor fan:

show the working status of the outdoor fan.

Reversing valve

electronic expansion valve

electrical heating

G1 valve

and other work status,

query can be directly observed through this interface.

Figure 5-1

5.2 Detailed Status Interface “C Parameters”

Click "

detail

" in the status query interface to enter the detailed status interface of the

machine, as shown in Figure 5-1. Click the arrow “->” button to return to the previous state
interface..

Figure 5-2

Summary of Contents for CX34






























































Search results

Summary of Contents for CX34

Reviews:

Related manuals for CX34

Brands by name

Popular brands

Chiltrix CX34, Installation And Operation Manual

Search results

Summary of Contents for CX34

Reviews:

Related manuals for CX34

Brands by name

Popular brands