Chiltrix CX34 Installation And Operation Manual Download Page 12 | Manualshive

Page: 12 / 61

background image

Chiltrix Inc.

www.chiltrix.com

Chiltrix Heat Pump Installation

Heat Pump Installation

Installation position

Note:

Installation must be carried out by professional personnel.

The recommended mounting pad should be at least 1 ½” above ground level. If you are in an area where snow
occurs, mount the unit high enough above grade to avoid blockage by drifting snow. You can consider a
properly rated wall mount if desired.
Proper drainage is required at the heat pump unit to avoid flooding the outdoor unit with water or ice. Make
sure condensate has a way to rapidly and completely drain away from the unit.
To install the unit on a balcony or on top of a building, the installation site must meet the allowable load
bearing capacity of the building structure without affecting the structural safety. Ensure the unit is well
ventilated; the direction of air exhaust should be kept away from the windows of neighboring buildings.
Adequate service clearance should be kept around the unit. The unit should not be installed in places
accompanied with oil, inflammable gases; corrosive components e.g. sulfur compound, or high-frequency
equipment.

Outdoor Unit Placement / Clearances
(Unit: mm) 200mm = 8” , 350mm =14 “,
400=16”, 500=20”,1000=40”

12

«
...
10
11
12
13
14
...
»

Summary of Contents for CX34






























































Reviews:

No comments

Related manuals for CX34

Brand: Waters Pages: 111

Infrared Heating

Brand: Jigsaw Pages: 11

Brand: VEHNS GROUP Pages: 18

GAU-NFA-HH-150K

Brand: Larson Electronics Pages: 12

Brand: Ultranatura Pages: 24

Brand: Daikin Pages: 44

Brand: Gabarron Pages: 8

Taro Pumps NCH 2250

Brand: Texmo Industries Pages: 34

FLOJET R3521/03521 Series

Brand: Xylem Pages: 4

Brand: Frico Pages: 14

KH 4256 AIR PUMP

Brand: ULTIMATE SPEED Pages: 72

Brand: RZTec Pages: 8

Brand: FLYGT Pages: 172

Brand: Lorell Pages: 14

Brand: Simer Pages: 16

Brand: Black+Decker Pages: 72

General Pump EV Series

Brand: Interpump Pages: 19

Brand: Teesa Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands