background image

H02782:01/05

7

WARNING

FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-

STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.  KEEP

INSTRUCTIONS FOR FUTURE USE.  

A PLASTIC POUCH IS ATTACHED TO

CRIB FOR PERMANENT STORAGE OF THE INSTRUCTIONAL LITERATURE.

BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR

DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR

SHARP EDGES.  DO NOT USE CRIB IF ANY PARTS ARE MISSING

OR BROKEN.  ASK YOUR DEALER OR WRITE TO Child Craft, P.O.

BOX 444, SALEM, IN 47167-0444 USA 1-877-265-9046 FOR RE-

PLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF

NEEDED.  

INCLUDE MODEL IDENTIFICATION NUMBERS WITH YOUR REQUEST WHICH

YOU RECORDED ON PAGE THREE.

  DO NOT SUBSTITUTE PARTS.

AFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.

  

IF

YOUR UNIT HAS A DROP SIDE.

WHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE

HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO

LONGER BE USED.

DO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM

BLINDS OR DRAPES MAY STRANGLE A CHILD.

IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR

CHILDREN’S PRODUCTS.

DO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED.  BE SURE

SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD

IS IN CRIB.

WHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET

MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS,

LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS

STEPS FOR CLIMBING OUT.

NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC

FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUF-

FOCATION.

DO NOT USE A WATER MATTRESS WITH THIS CRIB.

REPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF

EQUIPPED WITH TEETHING RAILS.)

STRINGS CAN CAUSE STRANGULATION!  DO NOT PLACE

ITEMS WITH A STRING AROUND A CHILD’S NECK, SUCH AS HOOD

STRINGS OR PACIFIER CORDS.  DO NOT SUSPEND STRINGS

OVER A CRIB OR ATTACH STRINGS TO TOYS.

REMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB

AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS

AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS

EARLIEST.  THESE TOYS CAN CAUSE STRANGULATION.

WHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE ANY ITEM

ATTACHED WITH WOOD SCREWS.

ALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY

CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE

CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY

IN PLACE.

ANY MATTRESS USED IN

THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES (69
CENTIMETERS), BY 51-5/8
INCHES (131 CENTIME-
TERS), WITH A THICKNESS
NOT EXCEEDING 6 INCHES
(15 CENTIMETERS).

THE DIMENSIONS OF THE MATTRESS
SHALL BE TAKEN FROM SEAM TO
SEAM OR EDGE TO EDGE WHERE AP-
PROPRIATE.

UPON COMPLETION OF

ASSEMBLY BE SURE ALL
SCREWS, BOLTS AND FAS-
TENING DEVICES HAVE
BEEN TIGHTENED SE-
CURELY.  A FREQUENT
CHECK SHOULD BE MADE
OF ALL SCREWS, BOLTS
AND FASTENING DEVICES
AND TIGHTEN IF NEEDED.

!

CHILD CRAFT INDUSTRIES, INC.

P.O. BOX 444

SALEM, IN 47167-0444  USA

PH:812-883-3111

FAX:812-883-1819

http://www.childcraftindustries.com

CAUTION

Summary of Contents for CONVERTS TO TODDLER BED AND FULL SIZE HEADBOARD AND FOOTBOARD








Reviews: