H02782:01/05
6
MAINTENANCE OF YOUR CHILD CRAFT BED:
Upon completion of assembly be sure all screws, bolts and fastening devices have been tightened
securely. A frequent check should be made of all screws, bolts and fastening devices and tightened if needed. Before each usage or assembly, inspect
crib for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT
use crib if parts are missing or broken. Contact
Child Craft
at
1-877-
265-9046
or
http://www.childcraftindustries.com
, for a replacement part or instructional literature if needed. Include Model Identification Number
with your request which you recorded on Page 3 of these instructions.
DO NOT SUBSTITUTE PARTS.
DO NOT MAKE ANY ALTERATIONS NOT
DESCRIBED IN THESE ASSEMBLY DIRECTIONS.
CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT BED:
Mix together a mild solution of gentle dishwashing liquid and water, apply to surface using
a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all surfaces thoroughly with a soft dry
cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE AND USE OF YOUR CHILD CRAFT BED:
A printed plastic pouch is attached to the crib spring for the permanent storage of the assembly
directions. After completing the assembly process you are advised to read and be aware of all
WARNINGS, CAUTIONS, CLEANING, STORAGE, USE
AND MAINTENANCE
notices contained in this set of directions and printed on the plastic pouch located on the underneath side of the crib spring. You
will then place the complete set of assembly directions into the plastic pouch for future referral. We caution you not to place excess hardware in the
plastic pouch as it could present danger to a child if retrieved. When storing crib use
CAUTION
as extreme temperature or humidity changes could be
harmful. Use
CAUTION
when a vaporizer is in use, always aim vapor stream away from crib as well as away from any wood furniture item.
Sketch B
(style may vary)
CRIB TO FULL SIZE:
Disassemble Crib by removing the mattress
and Spring
O
. Also remove Short Head Section
R
and Short
Foot Section
S
from Foot Posts
Q
and Stationary Posts
T
.
Store all removed parts and hardware as they will be needed for
future converting. Using (8) Allenhead Bolts
M
and (8) K-D Bolt
Plugs
Z
, attach the Stationary Side Assembly
U
/
T
/
W
and the
Long Foot Side Assembly
V
/
Q
to bed rails and slat roll (Models
#6454 and #6080 sold separately). Install Allenhead Bolts
K
and
Insert Nuts
L
, (2) of each in each Foot Posts
Q
and Stationary
Posts
T
as shown.
TODDLER BED TO FULL SIZE:
Disassemble Toddler Bed by re-
moving the mattress, Stretcher
X
and Spring
O
. Also remove
Short Head Section
R
and Short Foot Section
S
from Foot Posts
Q
and Stationary Posts
T
. Store all removed parts and hard-
ware as they will be needed for future converting. Locate Long
Foot Side
V
(not used on Toddler Bed). Attach Foot Posts
Q
to
Long Foot Side
V
using Allenhead Bolts
J
and tighten with Allen
Wrench
i
. Refer to
S
TEP
5 - D
IAGRAM
5
. Using (8) Allenhead Bolts
M
and (8) K-D Bolt Plugs
Z
, attach the Stationary Side Assem-
bly
U
/
T
/
W
and the Long Foot Side Assembly
V
/
Q
to bed
rails and slat roll (Models #6454 and #6080 sold separately).
Install Allenhead Bolts
K
and Insert Nuts
L
, (2) of each in each
Foot Posts
Q
and Stationary Posts
T
as shown.
V
/
Q
U
/
T
/
W
Model #6080 Slat Roll
K
L
K
L
L
L
Model #6454 Bed Rails
K
K
Sketch A
(style may vary)
WARNING
When use as a crib has been completed, you have the option to
convert to a Toddler Bed for years of additional use in your child’s
room. Refer to
S
TEP
6 - D
IAGRAM
6.
Remove Long Foot Side
V
.
Attach Stretcher
X
as shown in
Sketch A
. The dowel on each
end of Stretcher
X
locates in the top hole near the bottom of Foot
Posts
Q
. Secure with an Allenhead Bolt
M
and K-D Bolt Plug
H
at each end (shown installed). Fill the hole near the top of
each Foot Post
Q
with an Insert Nut
L
and Allenhead Bolt
N
as
shown. Tighten Allenhead Bolt
N
with Allen Wrench
i
and Insert
Nut
L
with Allen Wrench
I
.
Spring
O
O
O
O
O
must be installed in
lowest position in order for Stretcher
X
X
X
X
X
to prevent the
mattress from slipping off Spring
O
O
O
O
O
. Areas of entrap-
ment could cause serious injury or death.
Refer to
S
TEP
5 -
D
IAGRAM
5
for changing Spring
O
O
O
O
O
position
.
Store the removed
parts and hardware, they will be needed if you wish to convert
your Toddler Bed back to a Crib or into a Full Size Headboard and
Footboard.
PURCHASED MATTRESS
see size requirements
under WARNING
NOTE: Spring
O
must be installed
in lowest position as shown.
NOTE: When using as a Toddler Bed the mattress must have minimum
dimensions of 51-5/8 in. (1310mm) in length and 27-1/4 in. (690mm) in width
and 4 in. (100mm) in thickness but not to exceed 6 in.
It is very important that Stretcher
X
X
X
X
X
is used when converting to a Toddler
Bed. Failure to install this part could result in serious injury or death.
When using as a Toddler Bed, the minimum age shall not be less than 15
months and the maximum weight shall not be greater than 50 lb (22.7 kg).
!
S
N
M
H
H
M
L
X
N
R
U/T/W
M
M
C
ONVERT
TO
F
ULL
S
IZE
H
EADBOARD
AND
F
OOTBOARD
C
ONVERT
TO
T
ODDLER
B
ED
