H02782:01/05
3
Attach the short section of the
(4)
Scissor Arm Assemblies
A
A
A
A
A
to Spring
O
O
O
O
O
using
(4)
Pan Head Machine Screws
B
B
B
B
B
and
(4)
Lock Nuts
C
C
C
C
C
placed exactly
as shown in
Diagram 1
.
NOTE:
The metal threads of Lock Nuts
C
to be inserted first over Pan Head Machine Screws
B
B
B
B
B
as shown in Enlarged
Section View .
Be sure to use the proper receiving holes in Spring
O
O
O
O
O
as shown . This procedure will be accomplished from the underside of Spring
O
O
O
O
O
. Tighten all
(4)
Pan Head Machine Screws
B
B
B
B
B
while holding Lock Nuts
C
C
C
C
C
with a 7/16 inch wrench. Tighten each assembly securely.
Carefully remove and lay out all hardware and parts. During the assembly process whenever using screws or bolts (fastening devices), check each with
this hardware list, by letter and size identify by placing each fastening device on the diagram of the item which is sketched actual size. Be sure to use
the proper size specified in the assembly directions. Hardware Bag may contain extra fastening devices. Check quantities and match to
Hardware Bag
and Carton Parts Lists.
If a part is missing or broken contact Child Craft at PH: 1-877-265-9046, FAX: 812-883-1819,
http://www.childcraftindustries.com
for a replacement part or instructional literature. Before making this contact identify your crib. Model Identification numbers are on a label attached to the
inside face of Short Foot Section
S
S
S
S
S
bottom rail. Record the complete model identification number now: #____________________. Include this number with
a request for a part or literature for your crib.
DO NOT SUBSTITUTE PARTS!
Mount an End Plate - Right
E
E
E
E
E
and an End Plate - Left
D
D
D
D
D
to ends of each Stabilizing Bar
P
P
P
P
P
using
(4)
Pan Head Machine Screws
B
B
B
B
B
and
(4)
Lock Nuts
C
C
C
C
C
in each Stabilizing Bar
P
P
P
P
P
exactly as shown.
IMPORTANT: End Plates
D
D
D
D
D
&
E
E
E
E
E
must be positioned in the correct mounting holes to Stabilizing
Bars
P
P
P
P
P
exactly as shown.
Tighten down Pan Head Machine Screws
B
B
B
B
B
and Lock Nuts
C
C
C
C
C
securely using a phillips screwdriver and a 7/16 inch wrench.
See Enlarged View
UNDERSIDE OF SPRING
O
O
O
O
O
B
A
C
A
O
Long arm of Scissor Arm Assembly
A
Short arm of Scissor Arm Assembly
A
Long arm of
Scissor Arm
Assembly
A
Short arm of
Scissor Arm
Assembly
A
Plastic pouch
Lowest position
Middle position
Highest position
B
A
O
C
Enlarged View
Plastic insert in
Lock Nut
C
See Enlarged View
B
D
P
Enlarged View
Plastic insert in
Lock Nut
C
B
E
slot
slot
P
B
D
or
E
End Plate
INSTALL END PLATES
D
D
D
D
D
&
E
E
E
E
E
EXACTLY AS SHOWN
C
C
S
TEP
1 - D
IAGRAM
1: A
SSEMBLE
S
PRING
P
REPARATION
S
TEP
2 - D
IAGRAM
2: A
SSEMBLE
S
TABILIZING
B
ARS
