manualshive.com logo in svg

CHIEF LVM2X2U, Installation Instructions Manual, Page: 14 / 20

Share
Download
CHIEF LVM2X2U Installation Instructions Manual Download Page 14

LVM Series

Installation Instructions

14

Add-On Rail Installation (LVM3X2U/LVM3X3U
only)

1.

Install add-on rail (KK) to right column following instructions
in Rails Installation section.

2.

Use three #10-24 x 1 1/2" flat head cap screws (Z) to attach
each add-on rail (KK) to display rail (L). (See Figure 14)

Figure 14

Display Installation

1.

Place display face down on a soft, non-abrasive surface.

NOTE:

For best access, route display cables through columns
prior to display installation. See Cable Management
section for details.

CAUTION:

Using screws of improper diameter may

damage your display! Proper screws will easily thread into
display mounting holes.

2.

Select screw

diameter

 by examining hardware (A-C and F-

H) (6mm or 8mm) and comparing with mounting holes on
display. (See Figure 15)

3.

Select spacers:

•

If mounting holes are not recessed and interface
brackets (AA and BB) can lay flat against display,
then no spacers are required.

•

If mounting holes are recessed, or if protrusions
prevent brackets (AA and BB) from laying flat,
then spacers (E) must be used.

CAUTION:

Using screws of improper length may damage

your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.

4.

Select screw

length:

(See Figure 15)

•

Using your hand, insert SHORTEST length screw
of selected diameter (A or F) through 1/4" washer
(D), bracket (AA or BB), selected spacer (E, if
required), into display mounting hole. Do NOT
thread screw into hole at this time.

•

Proper screw length requires base of screw head
to protrude above flat washer a

distance equal to

or greater than the screw diameter.

 If screw

length is inadequate, select longer screw. Select

shortest

 screw which will protrude the required

distance.

5.

Use selected screws (A-C or F-H), washers (D) and spacers
(E), if necessary, to connect interface brackets (AA and BB)
to back of display. Make sure diamond on interface brackets
is even with center of display. (See Figure 15)

(Z) x 3

2

(KK)

Figure 15

(E) x 4, if necessary

(AA)

(BB)

(A-C or F-H) x 4

5

(D) x 4

(non-portrait models)

Summary of Contents for LVM2X2U





















Reviews:

No comments