Installation Instructions
FCA113
5
INSTALLATION
Locate Mounting Site
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the FCA113 does not exceed
250 lbs (113.4 kg) or the maximum weight limit of the specific
Fusion mount being attached. The maximum weight that can
be installed onto the FCA113 shelf is 30 lbs (13.6 kg).
IMPORTANT ! :
The FCA113 can be installed to a bare
8" concrete or 8"x8"x16" concrete block wall, or a 2" x 4"
wood studs wall covered by drywall with a maximum
thickness of 5/8".
IMPORTANT ! :
The minimum distance between
fasteners must meet the minimum distance requirements
for the mount to which it is being attached.
NOTE:
Proceed to either the
Installing to a Wood Stud Wall
section or the
Installing to a Concrete Wall
section.
NOTE:
If already installed, Fusion mount must be uninstalled
prior to FCA113 installation. Fusion hardware may be
discarded as the FCA113 mounting hardware will be
used to mount the FCA113 to wall.
WARNING:
Mounting holes previously used to mount
Fusion to wall may NOT be reused to install FCA113 to wall!
Drill all new holes for FCA113 installation.
Installing to a Wood Stud Wall
1.
Determine the center of the TV screen, and where it should
be located on the wall.
2.
Locate the closest 2" x 4" stud to the left and right of the
selected location.
NOTE:
If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3.
Line up the notches on accessory (A or B) with center of
screen marking to determine vertical center. (See Figure 1)
4.
Measure up 9.2" (233.7 mm) from the center point to mark
location of the upper mounting slots.
Figure 1
5.
Using a level, mark the wall on each stud to attach the
brackets through the upper mounting slots. (See Figure 2)
WARNING:
ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
WARNING:
EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
6.
Drill one 7/32" (5.5mm) pilot hole in each stud.
7.
Use two 5/16 x 2-1/2" lag bolts (M) and two 5/16" flat
washers (G) to attach top of brackets (A and B) to wall. (See
Figure 2)
NOTE:
If desired CPU location is off to the side of the display,
reverse brackets (A and B) from how they are shown in
Figure 2.
Figure 2
8.
Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
9.
Drill 7/32" (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 2)
10. Use two 5/16 x 2-1/2" lag bolts (M) and two 5/16" flat
washers (G) to attach the accessory to the wall through the
lower mounting holes. (See Figure 2)
11. Proceed to Installing Shelf to Brackets Section.
Center of screen
9.2"
Vertical center
of accessory
(233.7mm)
8
9
5
6
(G) x 4
7
10
(M) x 4
(A)*
(B)*
*reverse brackets to install CPU shelf to the outside
