background image

SKU 95596        

 For technical questions, please call 1-800-444-3353 

PAGE 9

INSpEcTION, mAINTENANcE, 

ANd clEANINg

1. 

WARNINg!  Always make sure 

the power Switch of the Inverter 

is in the “OFF” position and the 

unit is disconnected from its 

power source before perform-

ing inspection, maintenance, or 

cleaning procedures.
Before each use,

2. 

 

inspect the 

general condition of the Inverter. 

 

Check for misalignment or binding 

of moving parts, cracked or broken 

parts, damaged electrical wiring, 

and any other condition that may 

affect its safe operation.  If abnor-

mal heat, noise, or vibration occurs, 

have the problem corrected before 

further use.   

do not use damaged equipment.
To clean the exterior parts of the 

3. 

Inverter, use only a clean, dry 

cloth

.  

do not clean the unit with 

water or harsh cleaners.
This Inverter does not contain 

4. 

any replaceable parts.  

It the unit 

needs service, make sure to take it 

to a qualified service technician.

Make sure to store the Inverter in a 

5. 

clean, dry, safe location out of reach 

of children and other unauthorized 

people.

6. 

cAuTION!  All maintenance, 

service, or repairs not mentioned 

in this manual must only be 

performed by a qualified service 

technician.

TROuBlESHOOTINg

If the low battery alarm sounds, 

1. 

this means the input voltage is 

below the necessary 10.6 volts 

dc.

  The battery needs recharging.  

You should stop using the tool/ap-

pliance and then recharge the bat-

tery.  If this is not done, the Inverter 

will shut off automatically at around 

10.0 volts DC.

If you are unsure if the Inverter 

2. 

will have the proper amount of 

current to run a tool/appliance, 

use this rough guideline:  

Take 

the power consumption of the load 

in amps and multiply it by 120 

(output voltage).  The result will be 

the approximate number of watts 

needed to power the tool/appliance. 

Example:  

Load is rated at 26 

amps.  26 amps x

 

120 volts = 3120 

watts needed.  You can not use this 

device with the Inverter.

If your television will not turn on, 

3. 

it is important to keep in mind 

some appliances (including many 

televisions) may require two to 

six times their wattage to turn on.  

This Inverter will not work with such 

devices.

If your audio system buzzes 

4. 

while using this Inverter, it is be-

cause some sound systems can-

not filter out the modified sine 

wave produced by the Inverter.  

possible solution is to use a sound 

system that incorporates a higher 

quality power supply.

This Inverter is designed to mini-

5. 

mize the interference with televi-

sion signals.  

However, especially 

with weak television signals, some 

Summary of Contents for Power Systems 95596












Reviews: