Chevrolet Tavera Owner'S Manual Download Page 48

Page: 48 / 205

Fan control knob V

You may control the rate of airflow coming from the system by turning the fan

speed control knob. Turn the knob clockwise to increase the fan speed and

counterclockwise to decrease the fan speed.

Adjust the fan control knob from step 1 to step 4 as you wish.

Long-time maximum heating may cause fogged glass and poor visibility ahead.

So, please do not use maximum heating for a long time.

After long hours of parking under the blazing sun, be sure to open the windows and

doors to release the interior heat before starting the air conditioner (A/C).

Long-time maximum cooling pollutes the room air. Slide the Air intake/circulation

lever to intake outside air or open the windows for ventilation as required.

During cooling, the moist air is quickly cooled and it may look like mist from the air

outlet. This is normal.

Even when the air conditioner is not used, periodically operate the air conditioner

for several minutes with the engine idling so that the system does not run out of oil.

NOTE

Summary of Contents for Tavera














































































































































































































Search results

Summary of Contents for Tavera

Reviews:

Related manuals for Tavera

Brands by name

Popular brands

Chevrolet Tavera, Owner'S Manual

Search results

Summary of Contents for Tavera

Reviews:

Related manuals for Tavera

Brands by name

Popular brands