Chevrolet Tavera Owner'S Manual Download Page 78

Page: 78 / 205

(Continued)
The shoulder portion of the front seat belt has an “Emergency locking retractor”

which is designed to lock during a sudden stop or impact. At other times, it is

designed to move freely with the seat occupant. To unfasten the belts, push in the

center of the buckle.
When not in use, seat belts can be stowed by letting them rewound in their

retractors. If needed, move the keeper along the belt to let the belt retract fully.

This will also put the latch plate within easy reach on the door pillar.

Lap belts

Bring the latch plate adjuster across your body and clip it into the buckle. When this is

done correctly you will hear a “click”.

Adjust the belt length by pulling the belt end. Make sure the belts are fitted firmly

across your waist.

Summary of Contents for Tavera














































































































































































































Search results

Summary of Contents for Tavera

Reviews:

Related manuals for Tavera

Brands by name

Popular brands

Chevrolet Tavera, Owner'S Manual

Search results

Summary of Contents for Tavera

Reviews:

Related manuals for Tavera

Brands by name

Popular brands