Chevrolet Tavera Owner'S Manual Download Page 30

Page: 30 / 205

Brake system indicator light

The brake system indicator light comes on when the parking brake lever is pulled

with the starter switch “ON”, or the brake fluid in the reservoir is lower than the

specified level with the parking brake lever released.

WARNING

If the light turns on while driving, stop the vehicle immediately and check the level

of brake fluid in the reservoir. If the level is too low, have the vehicle towed in for

repairs.

Driving with malfunctioning brakes can lead to collision resulting in personal

injuries and damage to your vehicle and other property.

Low fuel warning lamp

This warning lamp comes on when the fuel tank is low on fuel. Fill up the fuel tank

as soon as possible when warning lamp comes on.

Do not let your vehicle to run out of fuel. This can lead to temporary air trap in fuel

system which will affect your next start after refueling.

CAUTION

Summary of Contents for Tavera














































































































































































































Search results

Summary of Contents for Tavera

Reviews:

Related manuals for Tavera

Brands by name

Popular brands

Chevrolet Tavera, Owner'S Manual

Search results

Summary of Contents for Tavera

Reviews:

Related manuals for Tavera

Brands by name

Popular brands