manualshive.com logo in svg

Chevrolet Orlando 2013, Owner'S Manual

Share
Download
Chevrolet Orlando 2013 Owner'S Manual Download Page 124

Black plate (24,1)

Chevrolet Orlando Owner Manual - 2013 - CRC - 6/5/12

5-24

Instruments and Controls

Remember, the Oil Life display
must be reset after each oil change.
It will not reset itself. Also, be
careful not to reset the Oil Life
display accidentally at any time
other than when the oil has just
been changed. It cannot be reset
accurately until the next oil change.
To reset the engine oil life system,
press the SET/CLR button while the
Oil Life display is active. See

Engine Oil Life System on
page 10

‑

9

.

Battery Voltage

This display, available on some
vehicles, shows the current battery
voltage. If the voltage is in the
normal range, the value will display.

For example, the display may read
BATTERY VOLTAGE 15.0 VOLTS.
The vehicle's charging system
regulates voltage based on the state
of the battery. The battery voltage
can fluctuate while viewing this
information on the DIC. This is
normal. See

Charging System Light

on page 5

‑

11

for more information.

If there is a problem with the battery
charging system, the DIC will
display a message. See

Battery

Voltage and Charging Messages on
page 5

‑

25

.

Blank Display

This display shows no information.

Vehicle Messages

Messages displayed on the DIC
indicate the status of the vehicle or
some action that may be needed
to correct a condition. Multiple
messages may display one after the
other.

The messages that do not require
immediate action can be
acknowledged and cleared by
pressing SET/CLR. The messages
that require immediate action cannot
be cleared until that action is
performed. All messages should be
taken seriously and clearing the
messages does not correct the
problem.

The following are some of the
vehicle messages that may be
displayed depending on your
vehicle content.

Summary of Contents for Orlando 2013





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands