manualshive.com logo in svg

Chevrolet Orlando 2013, Owner'S Manual, Page: 254 / 372

Share
Download
Chevrolet Orlando 2013 Owner'S Manual Download Page 254

Black plate (26,1)

Chevrolet Orlando Owner Manual - 2013 - CRC - 6/5/12

10-26

Vehicle Care

2. Remove the connector

retaining tab (1).

3. Disconnect the wiring harness

connector from the bulb (3) by
pressing the connector
release (2) and pulling
straight back.

4. Remove the bulb (3) from the

headlamp assembly by turning
counterclockwise and pulling
straight back.

5. Install the new bulb in the

headlamp assembly by turning
clockwise.

6. Install the wiring harness

connector to the bulb. Be sure
the connector release (2) locks
into place.

7. Install the connector

retaining tab (1).

Parking/Turn Signal Lamp

Passenger Side Shown, Driver
Side Similar

1. Parking Lamp

2. Turn Signal Lamp

To replace one of these bulbs:

1. Open the hood. See

Hood on

page 10

‑

4

.

2. For the driver side bulb, remove

the battery cover by firmly
pulling it straight up until it
releases.

3. Remove the bulb socket from

the headlamp assembly by
turning counterclockwise.

4. Remove the bulb from the bulb

socket by pulling straight out.

5. Install the new bulb in the bulb

socket.

6. Install the bulb socket into the

headlamp assembly by turning
clockwise.

7. On the driver side, replace the

battery cover.

Sidemarker Lamp

1. Remove the socket from the

lamp assembly by turning
counterclockwise.

Summary of Contents for Orlando 2013





















































































































































































































































































































































































Reviews:

No comments