manualshive.com logo in svg

Chevrolet Orlando 2013, Owner'S Manual, Page: 210 / 372

Share
Download
Chevrolet Orlando 2013 Owner'S Manual Download Page 210

Black plate (30,1)

Chevrolet Orlando Owner Manual - 2013 - CRC - 6/5/12

9-30

Driving and Operating

TCS/StabiliTrak Light

When the stability control system
activates, the TCS/StabiliTrak light
flashes on the instrument panel.
This also occurs when traction
control is activated. A noise may
be heard or vibration may be felt in
the brake pedal. This is normal.
Continue to steer the vehicle in the
intended direction.

If there is a problem detected
with StabiliTrak, SERVICE
STABILITRAK is displayed on the
Driver Information Center (DIC).
See

Ride Control System Messages

on page 5

‑

28

. When this message

is displayed and/or the TCS/
StabiliTrak light comes on and stays
on, the vehicle is safe to drive but
the system is not operational.
Driving should be adjusted
accordingly.

If the TCS/StabiliTrak light comes
on and stays on, reset the system:

1. Stop the vehicle.

2. Turn the engine off and wait

15 seconds.

3. Start the engine.

If the TCS/StabiliTrak light still
comes on and stays on at a speed
above 20 km/h (13 mph), see your
dealer for service.

TCS/StabiliTrak Button

TCS Off Light

StabiliTrak OFF

Light

StabiliTrak can be turned off if
needed by pressing and holding the
TCS/StabiliTrak button until the TCS
Off light and the StabiliTrak OFF
light come on. When StabiliTrak is
turned off, the system will not assist
with directional control of the vehicle
or limit wheel spin. Driving should
be adjusted accordingly. Press and
release the TCS/StabiliTrak button
again to turn both systems back on.

If cruise control is being used when
StabiliTrak activates, cruise control
will automatically disengage. Press
the cruise control button to
reengage when road conditions
allow. See

Cruise Control on

page 9

‑

31

for more information.

Summary of Contents for Orlando 2013





















































































































































































































































































































































































Reviews:

No comments