Chevrolet 2002 Impala Owner'S Manual Download | Manualshive

Page: 156 / 397

background image

2-90

This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running. If the light doesn’t come on, have it repaired.
This light will also come on during a malfunction in one
of two ways:
D Light Flashing

--

A misfire condition has been

detected. A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service may be required.

D Light On Steady

--

An emission control system

malfunction has been detected on your vehicle.
Dealer or qualified service center diagnosis and
service may be required.

If the Light Is Flashing

The following may prevent more serious damage to
your vehicle:
D Reducing vehicle speed.
D Avoiding hard accelerations.
D Avoiding steep uphill grades.
D If you are towing a trailer, reduce the amount of

cargo being hauled as soon as it is possible.

If the light stops flashing and remains on steady,
see “If the Light Is On Steady” following.

If the light continues to flash, when it is safe to do so,
stop the vehicle. Find a safe place to park your vehicle.
Turn the key off, wait at least 10 seconds and restart the
engine. If the light remains on steady, see “If the Light
Is On Steady” following. If the light is still flashing,
follow the previous steps, and drive the vehicle to your
dealer or qualified service center for service.

If the Light Is On Steady

You may be able to correct the emission system
malfunction by considering the following:

Did you recently put fuel into your vehicle?

If so, reinstall the fuel cap, making sure to fully install
the cap. See “Filling Your Tank” in the Index. The
diagnostic system can determine if the fuel cap has been
left off or improperly installed. A loose or missing fuel
cap will allow fuel to evaporate into the atmosphere.
A few driving trips with the cap properly installed
should turn the light off.

Did you just drive through a deep puddle of water?

If so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out. A few driving trips should turn the light off.

«
...
154
155
156
157
158
...
»

Summary of Contents for 2002 Impala














































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2002 Impala

Brand: Eclipse Pages: 6

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: Spiral Audio Pages: 2

Brand: Metra Electronics Pages: 8

Brand: M7 SPEED Pages: 6

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Brand: SNIPER Pages: 2

Brand: rough country Pages: 4

Brand: Whispbar Pages: 63

Brand: Pontiac Pages: 486

Crossland X 2017

Brand: Vauxhall Pages: 245

MAGICGRIP MGQDWD-CPO

Brand: Scosche Pages: 12

Brand: SSV Works Pages: 2

Brand: EUFAB Pages: 18

Brand: Audiovox Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands