background image

6.  Using the machine 

18 

 6.1 

 Foreward 

 

 

6.2  

Using the sieve 

  

 
 

7. Maintenance 

18 

 7.1 

 Foreward 

 

 

7.2      WEEE Waste of Electric and Electronic Equipment 

 

8.  Problems and solutions 

19 

 

8.1  

Problems, causes and solutions 

 

 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

17 

1.  Microswitch on the lever 

 

While the machine is running lift the presser until the microswitch ntervenes 
and stops the machine. 

 

Keep the presser still in the point in which the microswitch interve  nes and 
check that the space between the loading inlet and the presser is such to block 
fingers from entering. 

 

If this is not the case contact an authorized reseller or the manufac turer.    

2.  Microswitch on the container 

 

While the machine is running extract the plexiglass container and make sure 
that the machine stops. 

 

5.3 - Checking the efficiency of the stop pushbutton (fig. 4.1.1) 

While the machine is connected to the power supply and the utensil is moving 
press the pushbutton “2” fig. 4.1.1  
 

 

5.4 - Start up 

Set the differential switch fitted upstream at "I". The light indicator “3” fig.4.1.1 
will light up, indicating that the machine is powered 

Press the start pushbutton “2” (fig. 4.1.1) to start the machine. 

 
Note 

If the presser is in an “open” position the machine will not run, therefore it will have 
to be lowered. 

 

5.5 - Stop 

Press the stop pushbutton "1" fig 4.1.1 to stop the running of the machine; the 
light indicator “3” fig. 4.1.1 will remain on to indicate that the machine is powe-
red.  

Then set the differential switch installed upstream at "0", in this way disconnec-
ting the machine. 

 
Note 

Each time a work shift finishes or the machine is left to rest, the differential switch 
must be left set at “0”. 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GRATER HP 1,5











Reviews: