background image

TFX-D12 User Manual 

3  

2004-11-11/11:32 

B

EFORE 

Y

OU 

B

EGIN

 

What is included 

 

¾

 

1 x Stage Dimmer™ 12 (TFX-D12) 

¾

 Manual 

 

¾

 Warranty 

Card 

Unpacking Instructions 

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that 

all parts are present, and have been received in good condition. Notify the shipper immediately and 

retain packing material for inspection if any parts appear damaged from shipping or the carton itself 

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture 

must be returned to the factory, it is important that the fixture be returned in the original factory box 

and packing. 

Warning 

 

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction 
booklet. 

 

Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that 
stated on decal or rear panel of the fixture. 

 

This product is intended for indoor use only! 

 

To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit 
while operating. 

 

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation 
slots are blocked. 

 

Because Dimmer packs operate at potentially lethal high voltages, installation wiring should be done 
by qualified persons only! 
 
Do not connect chassis Ground to Neutral, or operate without chassis ground, otherwise the user 
could be exposed to potentially lethal voltages.  

Features 

 

 12-channel 

DMX-512 

dimmer/switch 

 

DMX-512 and Analog 0~10v DC 
control 

 

Each channel individually DMX 
addressable   

 

12 built-in beat-activated programs 
(stand-alone) 

 

10 Amp magnetic circuit breaker in 
each channel 

 

Individual dimmer modules 

 

LCD control panel is modular and  
can also be replaced 

 

Set preheat voltage to individual 
channel or all 

 

Dimmer curve selection; square, 
switch or linear 

 

AC phase correction 

 

Power failure memory 

 

Digital display and menu navigation 
buttons 

 

DMX signal loss failover function 

 

Thermal switch and short circuit 
protection 

 Fan 

cooled

 

Please read these instructions carefully, which includes important 

information about the installation, usage and maintenance? 

 

Summary of Contents for Stage Dimmer 12
















Reviews: