4. Operation
Page 22 of 96
MotionOrb™ User Manual Rev. 1
Configuring the
Slaves
Configure the slaves for Slave mode before configuring the master.
To configure a slave, do the following:
1. Make sure the product is connected to a power source.
2. Press
<MENU>
repeatedly until
MS
shows on the display.
3. Press
<ENTER>
.
Yes
or
No
shows on the display.
4. Use
<UP>
or
<DOWN>
to select
Yes
.
5. Press
<ENTER>
.
MS Master
shows on the display.
6. Use
<UP>
or
<DOWN>
until
No
shows on the display.
7. Press
<ENTER>
.
MS Mode
shows on the display.
8. Use
<UP>
or
<DOWN>
until the desired Master/Slave mode (
1
–
3
) shows on the display.
9. Press
<ENTER>
.
MS Address
shows on the display.
10. Use
<UP>
or
<DOWN>
until the desired MS address (
1
–
3
) shows.
11. Press
<ENTER>
.
MS
and
Yes
show on the display.
12. Press
<MENU>
.
Yes
stops showing on the display.
Configuring the
Master
Configure the master after all the slaves are configured and connected to it.
To configure the master, do the following:
1. Make sure the product is connected to a power source.
2. Press
<MENU>
repeatedly until
MS
shows on the display.
3. Press
<ENTER>
.
Yes
shows on the display.
4. Press
<ENTER>
.
MS Master
shows on the display.
5. Use
<UP>
or
<DOWN>
until
Yes
shows on the display.
6. Press
<ENTER>
.
MS Mode
shows on the display.
7. Use
<UP>
or
<DOWN>
until the desired Master/Slave mode (
1
–
3
) shows.
8. Press
<ENTER>
.
MS Address
shows on the display.
9. Press
<UP>
or
<DOWN>
until the desired MS address (
1
–
3
) shows.
10. Press
<ENTER>
.
MS
and
Yes
show on the display.
11. Press
<MENU>
.
Yes
stops showing on the display.
Once the master is configured, select Automatic or Sound mode. For more information see
Automatic Mode
or
Sound Mode
.
When MS shows on the display, the MotionOrb™ menu is at the Main programming level,
and pressing <MENU> scrolls through the main level functions.
Length Setting
The MotionOrb™ comes standard in a 2 meter length but MotionOrb™ Extensions can be
added to make the MotionOrb™ up to 4 meters long. Each extension is 1 meter long. The
Length setting configures the MotionOrb™ for the number of strings are attached.
To configure the MotionOrb™ length, do the following:
1. Press
<MENU>
repeatedly until
Length
shows on the display.
2. Press
<ENTER>
. A length option shows on the display.
3. Press
<UP>
or
<DOWN>
until the desired length shows on the display.
4. Press
<ENTER>
.
5. Press
<MENU>
. The desired length stops showing on the display.
The MotionOrb™ functions correctly only if the Length setting matches the total length of
orb strings installed. For example, if the MotionOrb™ is set to 4M, but the length is only 2
meters long, the effects macros will not display properly and the pixel mapping will not
work.
Summary of Contents for MotionOrb
