Chattanooga Group Intelect Legend XT 2760 User Manual Download Page 75

Page: 75 / 99

Intelect Legend XT® Therapy System

INSTALLATION/REMOVAL

INSTALLING THE CHANNEL 3/4 ELECTROTHERAPY AND NiMH BATTERY MODULE (CONTINUED)

Securing Therapy System to Module

Carefully place the Therapy System and

Module on one side. With a #1 Phillips

Screwdriver, install the four 4 mm x 20 mm

screws.
Tighten screws until the Module does not

move on the Therapy System.

Attaching the Lanyard

With a #1 Phillips Screwdriver, remove the

screw retaining the existing Front Access

Panel.
Install Lanyard to the new Extended Front

Access Panel using the same screw.

Do not twist Ribbon Cable. If power is

applied to the system with misalignment

of pins or a twisted ribbon cable, the

controlling electronics in the Module will

be destroyed and possible damage to the

System's internal components could occur.

Setting Therapy System onto Module

Set the Therapy System on the Module.

Make certain the Feet of the Therapy

System are resting in the Module Indents.

Summary of Contents for Intelect Legend XT 2760




































































































Search results

Summary of Contents for Intelect Legend XT 2760

Reviews:

Related manuals for Intelect Legend XT 2760

Brands by name

Popular brands

Chattanooga Group Intelect Legend XT 2760, User Manual

Search results

Summary of Contents for Intelect Legend XT 2760

Reviews:

Related manuals for Intelect Legend XT 2760

Brands by name

Popular brands