Chatsworth Products GlobalFrame GF Series User Manual Download

Page: 26 / 30

Power Management

One set of standard PDU brackets is included with the GF-‐Series GlobalFrame Gen 2 Cabinet.

Additional PDU brackets are available as well as a wide range of power strips and PDU’s, including

monitored and switched versions.

Standard PDU Brackets

39110-‐701

Two (2) brackets

Attaches to the cabinet vertical frame member

Full Height PDU Bracket

Dual, 4.8” (121 mm):

Two sizes: Dual and Wide

42U -‐

39086-‐X00

Attaches to the cabinet frame

45U -‐

39086-‐X03

Dual support 2 x 2.2”W (51 mm) PDUs

48U -‐

39086-‐X06

Wide support 2 x 2.7”W (69 mm) PDUs

52U -‐

39086-‐X10

Wide, 5.8” (147 mm):

42U -‐

39221-‐X00

45U -‐

39221-‐X03

48U -‐

39221-‐X06

52U -‐

39221-‐X10

X = Color (C=Black, E=Glacier White)

Summary of Contents for GlobalFrame GF Series































Search results

Summary of Contents for GlobalFrame GF Series

Reviews:

Related manuals for GlobalFrame GF Series

Brands by name

Popular brands

Chatsworth Products GlobalFrame GF Series, User Manual

Search results

Summary of Contents for GlobalFrame GF Series

Reviews:

Related manuals for GlobalFrame GF Series

Brands by name

Popular brands