background image

HARDWARE CONTENTS 

5

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install 

Solid fuels shall not be burned in this appliance.

the product.

This manual contains important information about the assembly, operation and maintenance of this 
fire pit. General safety information is presented in these first few pages and is also located throughout
the manual. Keep this manual for future reference and to educate new users of this product. This 
manual should be read in conjunction with the labeling on the product. Safety precautions are essential 
when any mechanical or propane fueled equipment is involved. These precautions are necessary when 
using, storing, and servicing. Using this equipment with the respect and caution demanded will reduce 
the possibilities of personal injury or property damage. The following symbols shown below are used 
extensively throughout this manual. Always heed these precautions, as they are essential when using 
any mechanical or fueled equipment.

DANGER

DANGER

DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance and
immediately call you gas supplier or fire department.

DANGER

FOR YOUR SAFETY: Surfaces of fire pit can remain 
extremely hot for a period after use. Allow 45 minutes to 
cool down before touching or moving the fire pit.

DANGER

Cover must be removed when burner is in operation.

DANGER

Failure to comply with the precautions and instructions
provided with this fire pit can result in death, serious 
bodily injury and property loss or damage from 
hazards of fire, explosion, burn, asphyxiation, and/or 
carbon monoxide poisoning. Only persons who can
understand and follow the instructions should use or
service this fire pit.

CC

BB

AA

Bolt
M6 X 12
Qty. 20

Screw
M5 X 10
Qty. 5

Screw
M4 X 5
Qty. 3

EE

Wrench

Qty. 1

DD

Washer

ø5

Qty.1

FF

Phillips

screwdriver

Qty. 1

WARNING:

THIS PRODUCT CAN EXPOSE YOU TO CARBON 

MONOXIDE, DI(2-ETHYLHEXYL) PHTHALATE (DEHP), WHICH 

IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER 

AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

For more information go to www.P65Warnings.ca.gov

Summary of Contents for FPC-C-02





















Reviews: