Position
cooler in win-
dow.
Position
neck of
cooler so that bottom of neck flange rests on window sill and flange
(E-Fig. 2) is snug against edge of sill (H-Fig. 2). With cooler in
position, hook the
US"
hooks into the holes of the top pan near the
back of the cooler (B-Fig. 2).
~WARNING:
Before doing any maintenance
be sure power is
off and unit is unplugged.
This is for your safety •
Fig. 6
Water Supply
L;",~
Iii
Maintenance
Float Rod
Fill pan.
Allow water to fill
to within I" of the top of the
overflow pipe and adjust float
to maintain this water level.
This can be accomplished by
bending
the Ooat rod (Fig.
6).
• Install
tloat valve.
Install
valve in the provided hole in
comer post (Fig. 6) and attach
water supply line.
Bottom Panel
Retainer
Fig. 3
Window Fill-In
Panels
• Install
window
panel
retainers.
Place
two
panel retainer strips onto
bottom
of neck flange
and position to the width
of the window.
Cut the
strips to fit if necessary.
These
strips
hold
the
window
fill-in
panels
(Fig. 3).
3 Lb.
I
3/4
Inches
~
~7.
• Check
belt tension.
A 3 lb. force
should deflect the belt 3/4 inches (see
Fig. 7). Readjust belt if needed.
Spring Start-Up
• Oil bearings.
The blower bearings and cooler motor in this unit
should be oiled with a few drops of non-detergent 20/30 weight oil
once each year. The motor docs not need oil if it has no oil lines
for oiling.
Motors that have no oil lines are lifetime oiled at the
factory and require no further oiling for the life of the unit.
I;--,CAUTlON:
Do not over
oil.
Over oiling can cause motor bum
out, due to excessive oil getting into
motor winding.
• Place window behind retainer
strip.
Raise back of cooler so that
the window (D-Fig. 2) may be brought down behind top of panel
retainer strip (C-Fig. 2).
• Break
fill-in panels
to fit.
With cooler installed, as described
above, measure for each window fill-in panel and score with sharp
knife and straight edge guide to desired width. To break window
fill-in panels, the panel should be laid over the edge ofa straight flat
surface at the point to be broken off. Apply pressure on the edge
of the panel that extends over the edge of the surface and break off
unwanted piece.
• Install fill-in panels.
Place one window 'fill-in panel on each side
of grill and into panel retainer strip at bottom of grill.
Place the
other panel retainer strips onto top of neck flange and fill-in panels.
Be sure the panels are snug up against cooler neck.
• Level Cooler.
Adjust the chains to level the cooler.
• Adjust house legs. Pull out house legs so that the rubbcr bumpers.
rest against house siding (F-Fig. 2). Tighten screw in retaining
collar. (G-Fig. 2).
• Replace
Pads.
Aspen pads should be replaced once or twice a
season, depending upon the length of the season. At the beginning
and at mid season a clean pad is more absorbent and efficient and
will deliver substantially more cool air .
• Clean pump.
Cleaning the pump is necessary once a year at start-
up. For your safety, tum unit offand unplug from power receptacle .
Remove the pump from the mount slot.
Remove the base of the
pump as shown in Fig. 8. Clean the pump and tum the impeller
to ensure free operation.
Remove the pump spout and check for
any blockage.
After cleaning,
reinstall the base onto the pump.
Press firmly to make sure it is
secure.
Reattach
the pump to
the mount in the cooler using
the plastic retainer to ensure that
the pump will not overturn.
Do
not forget to replace the spout
and water delivery tube onto the
Fig. 8
pump outlet.
Winter Shut Down
Drain water.
Always drain all of the water out of the cooler and
water supply line when not in use for prolonged periods, and par-
ticularly at the end ofthe season. Keep the water line disconnected
from both the unit and water supply so that it does not freeze.
• Cover unit. To protect the life of the finish, a cover for the unit is
suggested in extended periods of non use.
~ ~
Overflow
Pipe
~-Nipple
~-
Rubber Washer
~~BotiomPan
rt:JJ-
Nut
Fig. 4
Faucet
I
• Connect
water supply line.
In-
stall a sillcock and water valve on
faucet as shown by figure 5. Place
the nut and ferrule on the tubing
and tighten
the nut until water
tight.
Connecting Water
• Install
overflow
assembly.
Remove
nut and place nipple through the hole in
the pan, with the rubber washer between
the pan and the he.1.dof the drain nipple
(Fig. 4). Screw on nut and draw uptight
against bottom of pan. Insert overflow
pipe in nipple to retain water. Overflow
pipe may be removed to drain pan whcn
necessary. A garden hose may be
screwed
on the drain nipple to
drain water away from your unit.
110490-1
3
