background image

EXHAUST AND EVAPORATIVE EMISSION CONTROL SYSTEM WARRANTY

The following are speci

fic provisions relative to your Exhaust and Evaporative Emission Control System (ECS) Warranty 

Coverage

1.  APPLICABILITY:

 This warranty shall apply to 1995 and later model year California small off-road engines (SORE) (for other states, 

1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its 
original, end-use purchaser, and shall continue for 24 consecutive months thereafter.

2.  GENERAL EMISSIONS WARRANTY COVERAGE

 

CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent purchaser that each of its 
small off-road engines (SORE) is:

2a. Designed, built and equipped to conform to U.S. EPA emissions standards for spark-ignited engines at or below 19 kilowatts and 

all applicable regulations adopted by the California Air Resources Board and 

2b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects 

to the part as described in the engine manufacturer’s application for certification for a period of two years.

3.  THE WARRANTY ON EXHAUST AND EVAPORATIVE EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS:

3a. Any warranted part that is not scheduled for replacement as required maintenance in the Owner’s Manual shall be warranted for 

the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by CPE according 
to Subsection “d” below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the 
ECS Warranty Period.

3b. Any warranted, exhaust and evaporative emissions-related part which is scheduled only for regular inspection as specified in the 

Owner’s Manual shall be warranted for the ECS Warranty Period. A statement in such written instructions to the effect of “repair 
or replace as necessary”, shall not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty 
shall be warranted for the remainder of the ECS Warranty Period.

3c. Any warranted, exhaust and evaporative emissions-related part which is scheduled for replacement as required maintenance in 

the Owner’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for that part. If the part 
fails prior to the first scheduled replacement, the part shall be repaired or replaced by CPE according to Subsection “d” below. 
Any such exhaust and evaporative emissions-related part repaired or replaced under the ECS Warranty, shall be warranted for the 
remainder of the ECS Warranty Period prior to the first scheduled replacement point for such emissions-related part.

3d. Repair or replacement of any warranted, exhaust and evaporative emissions-related part under this ECS Warranty shall be 

performed at no charge to the owner at a CPE Authorized Service Outlet.

3e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered by the ECS Warranty is in 

fact defective, provided that such diagnostic work is performed at a CPE Authorized Service Outlet.

3f.  CPE shall pay for covered exhaust and evaporative emissions warranty repairs at non-authorized service outlets under the 

following circumstances:

i. The service is required in a population center with a population over 100,000 according to U.S. Census 2000 without a CPE 

Authorized Service Outlet AND

ii. The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile limitation does not apply in the 

following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska, Nevada, New Mexico, Oregon, Texas, Utah and 
Wyoming.

3g. CPE shall be liable for damages to other original engine components or approved modifications proximately caused by a failure 

under warranty of an emission-related part covered by the ECS Warranty.

3h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted exhaust and evaporative emission-related parts 

sufficient to meet the expected demand for such exhaust and evaporative emission-related parts.

3i.  Any CPE Authorized and approved exhaust and evaporative emission-related replacement part may be used in the performance 

of any ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not reduce CPE’s 
warranty obligation.

3j.  Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids this ECS Warranty and 

shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable hereunder for failures of any warranted 
parts of a CPE engine caused by the use of such an unapproved add-on or modified part.

Summary of Contents for 200978








































Reviews: