background image

 

Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board 
(CARB) Exhaust and Evaporative emissions regulations.

YOUR WARRANTY RIGHTS AND OBLIGATIONS:

The US EPA, California Air Resources Board, and CPE are pleased to explain the Federal and California Exhaust and Evaporative Emission 
Control Systems Warranty on your 2019 small off-road engine (SORE) and engine powered equipment. In California, new equipment that 
use small off-road engines (SORE) must be designed, built and equipped to meet the State’s stringent anti smog standards. In the other 
states, new engines and equipment must be designed, built and equipped, at the time of sale, to meet U.S. EPA regulations for small off-
road engines (SORE). CPE must warrant the exhaust and evaporative emission control system on your small off-road engine (SORE) for 
the period listed below, provided there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment 
leading to the failure of the exhaust and evaporative emission control systems.

Your evaporative emission control system may include parts such as: carburetors, fuel tanks, fuel lines, (for liquid fuel and fuel vapors), 
fuel caps, valves, canisters, filters, clamps, connectors, and other associated components. Also included for your exhaust emission control 
system may be fuel-injection system, the ignition system, catalytic converter and other exhaust emission related assemblies. Where a 
warrantable condition exits, CPE will repair your small off-road engine (SORE) at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This exhaust and evaporative emission control system is warranted for two years. If any exhaust and evaporative, emission related part on 
your engine or equipment is defective in, the part will be repaired or replaced by CPE.

OWNER WARRANTY RESPONSIBILITIES:

As the small off-road engine (SORE) owner, you are responsible for the performance of the required maintenance listed in your Owner’s 
Manual. CPE recommends that you retain all your receipts covering maintenance on your small off-road engine (SORE), but CPE cannot 
deny warranty coverage solely for the lack of receipts.

As the small off-road engine (SORE) owner, you should be aware that CPE may deny you warranty coverage if your small, off-road engine 
(SORE) or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. 

You are responsible for presenting your small off-road engine to an Authorized CPE distribution center, service center or alternative service 
outlet as described in (3)(f.) below or CPE dealer or CPE, Santa Fe Springs, Ca. as soon as the problem exists. The warranty repairs shall be 
completed in a reasonable amount of time, not to exceed 30 days. 

If you have any questions regarding your warranty coverage, you should contact:

Champion Power Equipment, Inc. 

Customer Service 
12039 Smith Ave. 

Santa Fe Springs, CA 90670 

1-877-338-0999 

[email protected]

CHAMPION POWER EQUIPMENT, INC. (CPE), 

THE UNITED STATES ENVIRONMENT PROTECTION AGENCY (U.S. EPA)  

AND THE CALIFORNIA AIR RESOURCES BOARD (CARB) EMISSION CONTROL SYSTEM WARRANTY

Summary of Contents for 100250







































Reviews: