background image

en-2

BEFORE YOU BEGIN

Leave room on the side of the motor for arms and installation work. Make sure to leave sufficient space.

Windload:

Even light wind may cause the motor to reverse (safety-reverse) as the forces effecting the gate are very high. This applies especially

to solid panel gates.

Note: An E-lock in combination with a floor locking device should always be installed in order to relieve the motor. In extreme cases strong wind
may bend fittings and door and /or damage the motor .

There are many important factors when deciding on the correct motor. Assuming a well functioning gate, the initial force is the most difficult
moment. When the gate is moving it generally requires a considerably smaller amount of force.

Gate Size:  

Gate size is an important factor. Wind can slow down gate or distort it, leading to higher amount of required  force.

Gate weight:  

Specification of gate weight represents only a rough parameter, which can vary according to actual  demand. Operation is

important.

Influence of temperature:

Low outdoor temperatures can impede or even prevent starting torque (ground deformation etc.). High outdoor

temperatures can lead to premature initiation of temperature protection (approx. 135°)

Attention:

Motors are not designed to run continuously (continuous operation). The motor warms up and can reach a temperature at which it

shuts down until operating temperature is reached again. Outside temperature and gate represent important parameters for actual operating
duration.

3x

Optional accessories

1.

Flashing lamp

2. ECK7

 

3.. Pfeilerbeschl

4. Padlock

5.

. E

-lock

6. Trafo f

or E-lock

FLA1-LED

Kit for cable extension of one

 

installation unit. Consists of 

m of 

cable 6-pole with identical colours, 

distribution box IP

44

, cable screw joints

 

and fastening material

2 pieces with large 4-hole baseplate 

 041ASWG-0092, 041ASWG-0090

  55124VO (2 keys per lock)

 203285 (12 Volts)

    207399

203339 (in combination with E-lock)

203315 standard

     

203322 high

      

041ASWG-ANT

TX4RUNI

771REV

41REV

8747EML

2

3

4

5

6

7

8

12

13

1

10

7. Floor locking

8 Stops for gates

9. 

External antenna

10. 

Remote control

11. 

Photocells

12. 

Key switch

13. 

Wireless keypad

1

1

9

Summary of Contents for TPD10-05





















Reviews: