background image

en 7  

20

21

22

23

Installation of photocells 

(Optional accessory)

Connecting the opener

Program opener and test

Setting the Limits

After installing and adjusting the door opener, photocells can be instal-

led� The instructions for installation are included in the scope of delivery 

of the light barrier and must be followed� 

The optional photocells 

ensure that the door is open, or remains open, if people, especially 

young children, are in the door area.

 By means of the photocells, a 

closing door is opened or an open door is obstructed from closing, if a 

person located in the door area interrupts the sensor beam� 

Photocells are particularly recommended for families with young 

children.

Connect opener in accordance with local rules and regulations to a

properly installed wall socket�

NOTE: When the opener is switched on, the operator light is also turned 

on for 2�5 minutes�

PROGRAMMING BUTTONS:

The programming buttons are located under a removable cover on the

back side of the garage door opener (see fig24).

1�  Press and hold the square Adjustment Button until the UP Button 

begins to flash.

 

2�  Press and hold the UP Button until the door is in the desired UP 

position� NOTE: The UP and DOWN Buttons can be used to move 

the door up and down as needed� 

3�  Once the door is in the desired UP position press and release the 

Adjustment Button. The garage door opener lights will flash and 

the DOWN Button will begin to flash.

 

4�  Press and hold the DOWN Button until the door is in the desired 

DOWN position� Make sure the rail does not bend� NOTE: The UP 

and DOWN Buttons can be used to move the door up and down as 

needed� 

5�  Once the door is in the desired DOWN position press and release 

the Adjustment Button. The garage door opener lights will flash 

and the UP Button will begin to flash.

 

6�  Press and release the UP Button� When the door travels to the pro 

grammed UP position, the DOWN Button will begin to flash. Note: 

IF the door does not travel to the UP position the travel limit pro-

gramming failed� Begin again with step1� If door travel is too short 

please refer to section 33 ”Frequently Asked Questions”� 

7�  Press and release the DOWN Button� The door will travel to the 

programmed DOWN position� Programming is complete�

Travel limits regulate the points at which the door will stop when moving 

up or down� Follow the steps below to set the limits�

This operator is equipped with a two speed system that is automatically 

set by the software� Canopy or 1-piece garage doors will automatically 

run in slow speed to insure a safe operation according regulatory� Doors 

traveling shorter than 190 cm will run automatically slow�

 

INTRODUCTION:

Your garage door opener is designed with electronic controls to make 

setup and adjustments easy� The adjustments allow you to program 

where the door will stop in the open (UP) and close (DOWN) position� 

The electronic controls sense the amount of force required to open and 

close the door� The force is adjusted automatically when you program 

the travel�

 

NOTE:

If anything interferes with the door’s upward travel it will stop� If anything 

interferes with the door’s downward travel, it will reverse� To watch a 

short instructional video on programming your new garage door opener 

use your smartphone to read the Code on this manuals back side

or visit www�chamberlain�eu�

The door opener should only be used if the operator can see 

the entire door area and is assured that it is free of obstac-

les and the door opener is set correctly� No one may pass 

through the door while it is moving. Before the first opening operation, 

check that all the facilities that are not needed are turned off. Remove 

all mounting aids and tools from the pivot area of the door�

Summary of Contents for MyQ LM75EVK





































Reviews: