Chamberlain HDSW24UL Installation Manual Download | Manualshive

Page: 52 / 64

background image

52

Entrapment Protection

LiftMaster monitored through beam photoelectric
sensor

Models LMTBUL and LMTBU

LiftMaster monitored retro-reflective photoelectric
sensor

Models LMRRUL and LMRRU

LiftMaster Monitered Commercial Protector
System

®

Models CPS-UN4 and CPSUN4G

LiftMaster monitored wireless edge kit (transmitter
and receiver)

Model LMWEKITU

LiftMaster monitored wireless edge transmitter

Model LMWETXU

Large profile monitored edge (82 ft. roll)

Model L50

Large profile ends kit (10 pair)

Model L50E

Small profile monitored edge (82 ft. roll)

Model S50

Small profile ends kit (10 pair)

Model S50E

Plastic channel

8 ft. (2.4 m) for both small and large profile edges (pack of 10).
Model L50CHP

Aluminum channel

10 ft. (3.1 m) for both small and large edge profiles (pack of 8).
Model L50CHAL

LiftMaster large profile monitored edges (4ft.,5ft., 6ft.)

Model L504AL, L505AL, L506AL

Remote Controls

LiftMaster offers a variety of LiftMaster remote controls to satisfy your application
needs. Single-button to 4-button, visor or key chain. The following remote controls are
compatible with operators manufactured by LiftMaster after 1993. Contact your
authorized LiftMaster dealer for additional details and options.

3-button remote control

The 3-button remote control can be programmed to control
the operator. Includes visor clip.
Model 893MAX

3-button mini-remote control

The 3-button remote control can be programmed to control
the operator. Includes key ring and fastening strip.
Model 890MAX

S 2.0

®

learning remote controls

One button can control a gate operator and the other(s)
can control garage door(s). It can also be programmed to
S

®

or S 2.0

®

code format.

Models 892LT and 894LT

Universal single and 3-button remote controls

Ideal for applications requiring a large number of remote
controls.
Models 811LM and 813LM

Keyless entry

Enables homeowner to operate gate operator from outside
by entering a 4-digit code on a specially designed keypad.
Model 877MAX

Wireless commercial keypad

Durable wireless keypad with blue LED backlight metal
keypad, zinc-alloy metal front cover and 5 year 9V lithium
battery. S 2.0

®

compatible.

Model KPW250

Commercial access control receiver

Access control receiver for up to 1,000 devices (any
combination of remote controls and wireless keyless
entries).
Model STAR1000

ACCESSORIES

«
...
50
51
52
53
54
...
»

Summary of Contents for HDSW24UL

































































Reviews:

No comments

Related manuals for HDSW24UL

Brand: Vector Pages: 54

Brand: Vector2 Pages: 52

Brand: Wayne-Dalton Pages: 22

Brand: Eagle Access Control Systems Pages: 32

Automatic Technology Battery Backup Gen 2...

Brand: B&D Pages: 8

Brand: Genius Pages: 32

CHAMBERLAIN CHAA250EVC

Brand: MyQ Pages: 116

SlideSmart CNX 15

Brand: Nice Pages: 48

Brand: Jaytech Pages: 13

Brand: tau Pages: 32

Brand: FAAC Pages: 11

Brand: Abloy Pages: 32

76606 - Pop-Top Electric Can Opener

Brand: Hamilton Beach Pages: 12

Brand: jcm-tech Pages: 11

Brand: Daspi Pages: 9

Brand: Raynor Pages: 32

Navigator 2245RGD

Brand: Raynor Pages: 36

Brand: Chamberlain Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands