manualshive.com logo in svg

Chamberlain HDSW24UL, Installation Manual

Share
Download
Chamberlain HDSW24UL Installation Manual Download Page 20

20

Plug In Transformer Power

Wire plug in transformer power as shown.

Plug in transformer

Control Board

Set switch to 

WALL XFMR

AC Power Switch

The AC switch on the operator turns the incoming 120/240 Vac power ON or OFF. The AC switch ONLY turns off AC power to the control board and DOES
NOT turn off battery power.

Battery Switch

The battery switch turns the battery power on or off.

AC Power Switch

Battery Switch

Step 9 Connect Batteries

7AH Batteries

The batteries are charged in the circuit by the integrated transformer.

1. Turn the AC power switch to OFF.

2. Turn the battery switch OFF .

3. Connect a jumper between the po) terminal of the battery to

the negative terminal(-) of the other battery.

4. Connect the red battery wire from the operator to the po)

terminal of the battery.

5. Connect the black battery wire from the operator to the negative (-)

terminal of the battery.

6. Turn the battery switch ON .

7. Turn the AC power switch to ON to restore AC power.

Battery Wiring

Red Wires

Black Wires

Jumper

INSTALLATION

Summary of Contents for HDSW24UL

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands