Chamberlain HDSW24UL Installation Manual Download Page 1

Page: 1 / 64

COMMERCIAL DC

VEHICULAR SWING GATE OPERATOR

INSTALLATION MANUAL

LiftMaster
300 Windsor Drive
Oak Brook, IL 60523

•

THIS PRODUCT MUST BE INSTALLED AND

SERVICED IN ACCORDANCE WITH THIS

MANUAL BY A TRAINED GATE SYSTEMS

TECHNICIAN ONLY.

•

This model is for use on vehicular passage

gates ONLY and not intended for use on

pedestrian passage gates.

•

This model is intended for use in Class I, II,

III and IV vehicular swing gate applications.

•

Visit LiftMaster.com to locate a professional

installing dealer in your area.

•

This gate operator is compatible with myQ

and S 2.0

accessories.

Access installation and technical support
guides or register this product

Send it in

by texting

the photo to 71403.

Take a photo

of the

camera icon including
the points ( ).

HDSW24ULTECH

Model

HDSW24UL

Summary of Contents for HDSW24UL

































































Search results

Summary of Contents for HDSW24UL

Reviews:

Brands by name

Popular brands

Chamberlain HDSW24UL, Installation Manual

Search results

Summary of Contents for HDSW24UL

Reviews:

Brands by name

Popular brands