Chamberlain C2212T Installation Manual Download | Manualshive

Page: 29 / 52

background image

29

Installation

STEP 14 Wire the Safety Reversing Sensors

If your garage has pre-installed wiring for the safety reversing sensors, see OPTION B - PRE-WIRED
INSTALLATION page 30.

OPTION A - INSTALLATION WITH NO PRE-WIRING

1.

Run the wire from both sensors to the garage door opener. Attach with staples, but DO NOT puncture
the wire.

2.

Separate the sensor wires and strip insulation from each end. Twist the two white wires together. Then
twist the two white/black wires together.

3.

Using a screwdriver, push in the terminal tabs, and insert the white wires into the white terminal.
Insert the white/black wires into the grey terminal.

Staple

7/16" (11 mm)

WHITE

WHITE

GREY

RED

1

2

3

HARDWARE

Insulated Staple (Not Shown)

«
...
27
28
29
30
31
...
»

Summary of Contents for C2212T





















































Reviews:

No comments

Related manuals for C2212T

Brand: quiko Pages: 32

CALYPSO 400 CA43

Brand: Erreka Pages: 46

Brand: Windmere Pages: 2

Safety Signal 3800RGD

Brand: Raynor Pages: 36

Brand: Clatronic Pages: 66

Brand: Cardin Elettronica Pages: 56

Brand: Key Automation Pages: 24

Brand: V2 ELETTRONICA Pages: 92

Brand: Roger Technology Pages: 49

BRUSHLESS B70/2DC

Brand: Roger Technology Pages: 116

Brand: Roger Technology Pages: 8

Brand: Eagle Pages: 20

Brand: DITEC Pages: 18

MULTITELESCOPIC

Brand: Fac Pages: 8

Brand: Pujol Pages: 20

Brand: Pujol Pages: 36

Mini Marathon Pro Q

Brand: Pujol Pages: 76

Brand: Gate Tel Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands