Chamberlain C2212T Installation Manual Download | Manualshive

Page: 3 / 52

background image

Installation Manual

Chain Drive Garage Door Opener

Models C2212T • C2405

FOR RESIDENTIAL USE ONLY

PRE

ǫ

PROGRAMMED REMOTE

CONTROL INCLUDED

To register your garage door opener to receive
updates and offers from Chamberlain, visit
chamberlain.registria.com or use the icon below:

www.chamberlain.com

1.

Take a photo of the camera icon including
the points (

).

2.

Send it in by texting the photo to 71403 (US).

•  Please read this manual and the enclosed safety materials carefully!
•  Fasten the manual near the garage door after installation.
•  The door WILL

NOT

CLOSE unless the Protector System® is connected and properly aligned.

•  Periodic checks of the garage door opener are required to ensure safe operation.
•  The model number label is located on the back panel of your garage door opener.
•  This garage door opener is compatible with myQ® and S 2.0® accessories.
•  DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended

devices and features are to be used ONLY with sectional doors.

«
1
2
3
4
5
...
»

Summary of Contents for C2212T





















































Reviews:

No comments

Related manuals for C2212T

Brand: Calimet Pages: 3

Open Ease Can Openers

Brand: Hamilton Beach Pages: 10

Brand: quiko Pages: 22

Brand: Chamberlain Pages: 286

Brand: Microbrain Intelligent Technology Pages: 32

Brand: DS Produkte Pages: 8

Brand: Nice Pages: 44

Brand: Nice Pages: 44

Brand: US Automatic Pages: 23

SL-3000-UL SERIES

Brand: Elite Pages: 31

Brand: Chamberlain Pages: 48

ATS 211X 1/2 HP

Brand: Chamberlain Pages: 64

Brand: quiko Pages: 42

Brand: Vogue Pages: 28

Brand: FAAC Pages: 4

Brand: Zero Pages: 12

76375 - CleanCut Extra-Tall Can Opener

Brand: Hamilton Beach Pages: 2

Brand: Wayne-Dalton Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands