Chamberlain C2212T Installation Manual Download

Page: 13 / 52

Assembly

STEP 5 Tighten the Chain

Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.

To tighten the chain, turn the outer nut in the direction shown.

When the chain is approximately 1/4" (6 mm) above the base of the rail at it's midpoint, retighten the
inner nut to secure the adjustment.

Sprocket noise can result if the chain is too loose. When installation is complete, you may notice some chain
droop with the door closed. This is normal. If the chain returns to the position shown when the door is open,
do not re-adjust the chain.

NOTE:

During future maintenance, ALWAYS pull the emergency release handle to disconnect the trolley before

adjusting the chain.

Outer
Nut

Lock
Washer

Trolley
Threaded
Shaft

Inner Nut

To Tighten
Inner Nut

To Tighten Outer Nut

Base of Rail

Mid length of Rail

Chain

1/4" (6 mm)

STEP 6 Install the Sprocket Cover

MODEL C2212T

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

ALWAYS keep hand clear of sprocket while operating opener.

Securely attach sprocket cover BEFORE operating.

Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with #8x3/8"
hex screws provided.

Hex Screw #8x3/8"
(Packed with the sprocket cover)

HARDWARE

Hex Screw

Sprocket Cover

You have now finished assembling your garage door opener. Please read the following warnings before
proceeding to the installation section.

Summary of Contents for C2212T





















































Search results

Summary of Contents for C2212T

Reviews:

Related manuals for C2212T

Brands by name

Popular brands

Chamberlain C2212T, Installation Manual

Search results

Summary of Contents for C2212T

Reviews:

Related manuals for C2212T

Brands by name

Popular brands