Chamberlain 8355W Manual Download Page 49

Page: 49 / 52

Repair Parts

Models 8360W, 8360WL, and 8360WLB

RAIL ASSEMBLY PARTS

Description

Part Number

Chain - for 7 foot door

041D3484

Chain - for 8 foot door

041D3483

Chain - for 10 foot door

041D3485

Chain Pulley Bracket

041A4813

Master link

004A1008

One-Piece Rail 7 feet (2.1 m)

1707LM

One-Piece Rail 8 feet (2.4 m)

1708LM

One-Piece Rail 10 feet (3 m)

1710LM

Trolley Assembly Includes:
Threaded Shaft (1), Nuts (2), Washer (1),
Clevis Pin (1), Ring (1), Master Link (1),
Chain Extension

041A3489

Trolley Threaded Shaft

041A6689

ACCESSORIES

Description

Part Number

Motion detecting control panel

886LMW

3-button remote control

893LM

INSTALLATION PARTS

Description

Part Number

Curved door arm

041B0035B

Door bracket with clevis pin and fastener

041A5047

Emergency release rope and handle

041A2828

Header bracket with clevis pin and fastener

041A4353

Remote control visor clip

K029B0137

Safety sensor bracket

041A5266-3

Safety sensor kit with receiving and
sending sensors with 3 feet (.9 m) 2-
conductor wire

041A5034

Straight door arm

4178B0034B

White and red/white wire

041B4494-1

3V CR2032 lithium battery

K010A0020

Extension bracket (optional)

041A5281-1

Not Shown

Installation hardware bag

041A2770-6

User’s Guide

114A5288

Summary of Contents for 8355W





















































Search results

Summary of Contents for 8355W

Reviews:

Related manuals for 8355W

Brands by name

Popular brands

Chamberlain 8355W, Manual

Search results

Summary of Contents for 8355W

Reviews:

Related manuals for 8355W

Brands by name

Popular brands