background image

36

Operation

Using the Multi-Function Door Control

SYNCHRONIZE THE DOOR CONTROL

To synchronize the door control to the garage door opener, press the push bar until the garage
door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar,
each press of the push bar will activate the garage door opener.

Up to 2 Smart Control Panels

®

or 4 of any other S 2.0 door controls can be connected to the

garage door opener.

Push Bar

LIGHT Button

SERVICE LED

LOCK Button

COMMAND LED

LEARN Button

PUSH BAR

Press the push bar to open or close the door.

LIGHT BUTTON

Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned on
they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated.
Once the garage door opener is activated the lights will turn off after the specified period of time (the
factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in
motion.

The following features are accessible by lifting up the push bar:

LEARN A DEVICE

Any compatible remote controls, wireless keyless entry, Wi-Fi garage door openers, or myQ

®

accessories can be programmed to the garage door opener by pressing the LEARN button on the door
control.

LOCK

The LOCK feature is designed to prevent activation of the garage door opener from remote controls
while still allowing activation from the door control and keyless entry. This feature is useful for added
peace of mind when the home is empty (i.e. vacation).

AUTOMATIC LIGHT

Light Feature

The lights will turn on when someone enters through the open garage door and the safety reversing
sensor infrared beam is broken.

MAINTENANCE ALERT (MAS)

This feature assists the homeowner in ensuring the garage door opener system stays in good working
condition. When the garage door opener needs to be serviced (approximately 4500 garage door
opener cycles) the command (yellow) and service (red) LEDs will begin to alternately flash back and
forth. The factory setting for the MAS feature is off and can be activated at time of installation. Contact
your installing dealer for service.

Summary of Contents for 8355W





















































Reviews: