3
Palmgren Operating Manual & Parts List 9681061C
SAFETY RULES (CONTINUED)
TOOL SHOULD BE MAINTAINED
•
Always unplug tool prior to inspection.
•
Consult manual for specific maintaining and adjusting proce-
dures.
•
Keep tool lubricated and clean for safest operation.
•
Remove adjusting tools. Form habit of checking to see that ad-
justing tools are removed before switching machine on.
•
Keep all parts in working order. Check to determine that the
guard or other parts will operate properly and perform their in-
tended function.
•
Check for damaged parts. Check for alignment of moving parts,
binding, breakage, mounting and any other condition that may
affect a tool’s operation.
•
A guard or other part that is damaged should be properly re-
paired or replaced. Do not perform makeshift repairs. (Use parts
list provided to order repair parts.)
KNOW HOW TO USE TOOL
•
Use right tool for job. Do not force tool or attachment to do a
job for which it was not designed.
•
Disconnect tool when changing abrasive belt or disc.
•
Avoid accidental start-up. Make sure that the tool is in the OFF
position before plugging in.
•
Do not force tool. It will work most efficiently at the rate for
which it was designed.
•
Use of improper accessories may cause risk of injury to persons.
•
Handle workpiece correctly. Protect hands from possible injury.
•
Turn machine off if it jams. Belt jams when it digs too deeply
into workpiece. (Motor force keeps it stuck in the work.)
•
Never leave tool running unattended. Turn power off and do
not leave tool until it comes to a complete stop.
•
Do not overreach. Keep proper footing and balance.
•
Never stand on tool. Serious injury could occur if tool is tipped
or if belt or disc is unintentionally contacted.
•
Keep hands away from moving parts and sanding surfaces.
•
Know your tool. Learn its operation, application and specific lim-
itations.
•
Support workpiece with miter gauge, work stop or work table.
•
Maintain 1/16˝ maximum clearance between table and sanding
belt or disc.
CAUTION:
Think safety! Safety is a combination of operator com-
mon sense and alertness at all times when tool is being used.
WARNING:
Do not attempt to operate tool until it is completely
assembled according to instructions.
SPECIFICATIONS
Belt size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 42˝, 80 grit
Belt platen area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1
⁄
4
x 2˝
Belt table dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
⁄
4
x 9˝
Belt table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 60º
Belt speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4480 FPM
Disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6˝, 80 grit
Disc table dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1
⁄
8
x 8˝
Disc table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 45º
Disc dust collection chute . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1
⁄
2
˝ diameter
Disc speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3590 RPM
Base dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5
⁄
8
x 9˝
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SP, locking rocker
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120V, 3.5 AMPS
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 lbs
Shipping weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 lbs
ASSEMBLY
Refer to Figures 1 through 3.
CAUTION:
Do not attempt assembly if parts are missing. Use this
manual to order repair parts.
ATTACH ABRASIVE DISC TO ALUMINUM DISC
1. Remove dust chute by loosening screws and bolts.
2. Remove the adhesive cover from the back of the abrasive disc.
3. Center abrasive on aluminum disc and press to paste.
4. Make sure abrasive is pasted evenly on the aluminum disc.
5. Replace dust chute.
ASSEMBLE DISC TABLE
Refer to Figure 1.
1. Slide table onto disc guard as shown.
2. Set the disc table at right angle to the aluminum disc and se-
cure the table position using two knobs and flat washers
ADJUST DISC TABLE ANGLE
Refer to Figure 1.
1. The disc table is adjustable from 0 to 45 degree for beveled
work. To adjust disc table, loosen 2 knobs and flat washers and
adjust to desired angle
2. Use scale on disc table trunnions to set disc table from 0 to 45
degree to abrasive disc
3. When disc table is at desired angle, lock into position by tight-
ening the knobs
Figure 1 - Assemble and adjust disc table.
