Centrometal BioTec Plus Technical Instructions Download Page 34 | Manualshive

Page: 34 / 52

Centrometal BioTec Plus Technical Instructions Download Page 34

Factory: Super control

OFF, Supervision, Super control

This option is used to set and enable/disable
internet supervision.

This option allows you to set the time zone if the
boiler is in a different time zone than the web portal
server. (this option must be set if you enable "Time
syncronisation option")

This option allows you to reset connection with
home network.

This option allows you to enter the name of WiFi
home network to which you want to connect the "Cm
WiFi box" and the boiler. You must enter exact WiFi
network name or else boiler will not able to connect to
the WiFI network.

This option allows you to enter a password for your
home Wi-Fi network. You must enter exact password
or else boiler will not be able to connect to the WiFi
network.

This option allows boiler time synchronization with
web server time (internet time).

Internet supervision

Technical instructions CONTROL UNIT

BioTec Plus

34

«
...
32
33
34
35
36
...
»

Summary of Contents for BioTec Plus





















































Reviews:

No comments