Centrometal BioTec Plus Technical Instructions Download Page 15 | Manualshive

Page: 15 / 52

Centrometal BioTec Plus Technical Instructions Download Page 15

Use the left side of the boiler - Fuel: wood, ignition

2.0 USE THE LEFT SIDE OF THE BOILER - FUEL: WOOD

2.1 IGNITION

Boiler must not be used in flammable and explosive environment. It must not be used by children or
disabled persons (either physically or mentally), as well as by person without knowledge or
experience, unless they are under control or trained by s person responsible for their safety. Children
must be supervised in the vicinity of the product. Protective gloves must be used!

Protective gloves must be used!

NOTE:

Before ignition make sure that is left side of the boiler selected like active (see indicator „A” on
figure below) (for procedure for choosing boiler side for work (used fuel) view point 1.1 „Choosing
boiler side (choosing fuel)” in this technical instructions).

IGNITION PHASE:

- Open upper and middle boiler doors (see pages 4 and 5 in Technical instructions for BioTec Plus
boiler - BOOK 1/2)

Follow these steps for succesfull igniton phase:

- press button for boiler start
- on display will be displayed window for
boiler start
- press ”OK” button

A

Technical instructions CONTROL UNIT

BioTec Plus

15

«
...
13
14
15
16
17
...
»

Summary of Contents for BioTec Plus





















































Reviews:

No comments