Central Machinery 32650 Set Up And Operating Instructions Manual Download Page 21 | Manualshive

Page: 21 / 26

background image

Page 21

For technical questions, please call 1-800-444-3353.

SKU 32650

Figure 28

Belt (34)

Spindle

Pulley

(38)

Motor

Pulley

(3e)

Bolts

(35)

Motor

Bracket

(36)

Bolts

(35)

5. Remove the old Belt (34) and place a

new belt on the Pulleys (3e and 38).
If the tension needs adjusting:

6.

Loosen the four hex head Bolts (35) on

a.

the Motor Bracket (36).
Slide the bracket up or down until the

b.

sides of the belt are tight.
Tighten the bolts and make sure the belt

c.

runs straight.

nOTe:

Never over-tension belt as this will

result in shortened motor bearing life.
Replace the belt guard and turn the

7.

machine right side up.

carbon Brush replacement

Replacement Carbon Brushes (3b)

are included with this unit. The Carbon

Brushes should be replaced by a

qualified technician.

reV 10e

«
...
19
20
21
22
23
...
»

Summary of Contents for 32650



























Reviews:

No comments

Related manuals for 32650

Brand: Rapid Pages: 6

Brand: OK-WINDER Pages: 2

Brand: OMCN Pages: 13

Brand: WABCO Pages: 24

Aquajoe FIBERJACKET AJFJH50-58-PRO-RM

Brand: SNOWJOE Pages: 8

GREEN POWER CCTV BNC04124

Brand: Pulsar Pages: 8

Brand: Grizzly Pages: 48

Brand: Milwaukee Pages: 45

Brand: Milwaukee Pages: 4

Brand: Metabo Pages: 72

Brand: B&B Electronics Pages: 6

Brand: M-system Pages: 2

Brand: Ironton Pages: 9

Brand: Far Tools Pages: 17

Brand: Panduit Pages: 2

Brand: Xantrex Pages: 76

Brand: Baileigh Pages: 24

Brand: Kärcher Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands