Central Machinery 32650 Set Up And Operating Instructions Manual Download Page 8

Page: 8 / 26

Page 8

For technical questions, please call 1-800-444-3353.

SKU 32650

SPeciFicaTiOnS

Electrical Input

120 V~, 60 Hz, 7/8 HP

Motor No Load Speed 11,500 RPM
Max. Accessory

Diameter

2”

Shank Diameter

Router: 1/4”

Shaper: 1/2”

Table Top

11-3/4” x 9-3/4” surface

unPacking

When unpacking, make sure that the

item is intact and undamaged. If any parts

are missing or broken, please call Harbor

Freight Tools at 1-800-444-3353 as soon as

possible.

components

Figure 1

Table Insert (8)

Carbon

Brushes

(3b)

Belt (34)

Double Ended Wrench (55)

Nut (49)

Spindle Wrench (54)

Keyed Washer (48)

Switch Key (27b)

Washer (13)

Radius Pin (6)

Collar (53)

Router Bit

Collet (50)

Shaper

Spindle

(47)

Router Collet Nut (51)

Nut (56)

Table Top

(7)

Miter

Gauge

Assembly

(1)

Ring Guard (11)

Fence Assembly (2)

Chip Discharge Chute (9)

Switch

(27a)

Base (25)

reV 10e

Summary of Contents for 32650



























Search results

Summary of Contents for 32650

Reviews:

Related manuals for 32650

Brands by name

Popular brands

Central Machinery 32650, Set Up And Operating Instructions Manual

Search results

Summary of Contents for 32650

Reviews:

Related manuals for 32650

Brands by name

Popular brands