Central Machinery 32650 Set Up And Operating Instructions Manual Download Page 23

Page: 23 / 26

Page 23

For technical questions, please call 1-800-444-3353.

SKU 32650

reV 10e

record Product’s Serial number here:
note:

If product has no serial number, record month and year of purchase instead.

note:

Some parts are listed and shown for illustration purposes only, and are not available

individually as replacement parts.

PleaSe read The FOllOWing careFullY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE

OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY

CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Summary of Contents for 32650



























Search results

Summary of Contents for 32650

Reviews:

Related manuals for 32650

Brands by name

Popular brands

Central Machinery 32650, Set Up And Operating Instructions Manual

Search results

Summary of Contents for 32650

Reviews:

Related manuals for 32650

Brands by name

Popular brands