1. GENERAL INFORMATION
Thank you for your purchase of
CEL-MAR Company
product. This product has been completely tested and is covered by a two year
warranty on parts and operation from date of sale.
If any questions or problems arise during installation or use of this product, please do not hesitate to contact Technical Support at +48
41 362-12-46 or e-mail [email protected].
1.1. WARRANTED INFORMATION
ADA-1040PC3
converter is covered by a two year warranty from date of sale. In case of being damaged it will be repair or the
damaged component will be replace. The warranty does not cover damage caused from improper use, materials consumption or any
unauthorized changes. If the product does not function (is damaged), or not operate in accordance with the instructions, will be
repaired or replaced.
All warranty and no warranty repairs must be returned with paid transport and insuring to the
CEL-MAR Company.
CEL-MAR Company
under no circumstances won't be responsible for ensuing damage from improper using the product or as a result
of random causes: the lightning discharge, the flood, the fire and the like.
CEL-MAR Company
is not be held responsible for damages and loss including: loss of profits, loss of data, pecuniary losses ensuing
from using or the impossibility of using this product.
In specific cases
CEL-MAR Company
discontinue all warranties and in particular do not follow the user manual and do not accept
terms of warranty by the user.
1.2. GENERAL CONDITIONS FOR SAFE USE
The device should be installed in a safe and stable places (eg, electroinstallation cabinet), the powering cable should be arranged so
as not to be exposed to trampling, attaching, or pulling out of the circuit.
Do not put device on the wet surface.
Do not connect devices for nondescript powering sources,
Do not damage or crush powering wires.
Do not make connection with wet hands.
Do not adapt, open or make holes in casings of the device!
Do not immerse device in water or no other liquid.
Do not put the fire opened on device sources: candles, an oil lamps and the like.
Complete disable from the supply network is only after disconnecting the power supply circuit voltage.
Do not carry out the assembly or disassembly of the device if it is enabled. This may result to short circuit and damage the device.
The device can not be used for applications that determine human life and health (eg. Medical).
1.3. CE LABEL
The CE symbol on the device CEL-MAR means compatibility with electromagnetic compatibility Electromagnetic
Compatibility Directive
EMC 2014/30/WE.
Declaration of Conformity is available by contact with Technical Service
(email: [email protected]; phone: +48 41 362-12-46).
1.4. ENVIRONMENTAL PRESERVATION
This sign on the device inform about putting expended device with other waste materials. Device should send to the
recycling. (In accordance with the act about the Electronic Appliance Expended from day 29 of July 2005)
1.5. SERVICE AND MAINTENANCE
Converter ADA-1040PC3 does not require the servicing and maintenance.
Technical support is available at 48 41 362-12-46 in 8.00-16.00, from Monday to Friday or e-mail
.
1.6. PACK CONTENTS
The converter is delivered with the user manual, Line terminators resistors: Rt=120
W
(2 pcs.), CD with ADAConfig software.
2. PRODUCT INFORMATION
2.1. PROPERTIES
●
Conversion of protocols Soladin – SunMaster (RS232) to MODBUS-RTU (RS485/422) and inversely,
●
Parameters, baud rate and data format conversion between RS485/RS422 and RS232 converter's ports,
●
Operating on 2 or 4 wire buses in RS485/RS422 standard in point-to-point and multipoint mode,
●
Conversion TX, RX signals of RS232 standard to RS485/RS422 standard and inversely,
●
Operation up to 32 devices on RS485 bus,
●
Baud rate set on RS232 & RS485/RS422 interfaces (bps): 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 14400, 19200, 28800,
38400, 57600, 76800, 115200, 230400,
●
Data format set on RS232 & RS485/RS422 interfaces: data bit: 5, 6, 7, 8; parity: None, Odd, Even; number of stop bits: 1, 2,
●
Power supply 10 - 30 VDC stable min. 2W,
●
~3kV= optoisolation in signal channel between RS232 and RS485/422 interfaces,
●
1kV= or 3kV= galvanic isolation between RS232 & RS485/422 interfaces and power supply (depend on version),
●
Implemented short circuit protection and over-voltage protection on RS485 / RS422 network,
●
Implemented ESD 15kV surge protector of RS232 interface,
●
Implemented protection against power supply reverse connection,
●
Connection RS485/RS422 network and power supply via screw terminal block 2.5 mm
2
.
●
DB-9F connector for cable connection of RS232 interface to PC, controller etc.
●
Cover compatible with DIN 43880 standard– mounting in typical electro-installation unit,
●
Cover adapt to rail mounting according to DIN35 / TS35 standard,
3
ADA-1040PC3
Summary of Contents for ADA-1040PC3
Page 23: ...23 ADA 1040PC3...
