6
Start making ice cream
After stirring shaft and the valve element properly installed, you can be added to the raw material
- -
When using the soft ice cream powder, cream powder please per 1 kg against 2.5 liters of purified water to 3 formulated feed. Prior to joining the ratio of raw materials, please check again
1. Turn on the power, the power switch to the "ON (ON)" position, the screen display "may be a normal operation"
2. Insert the expanded tube, one end of the silicone tube is connected to the intake pipe of metal, the other end connected to the top of the pot to supply outlet
3. First
2 l
Feedstock into the pot, so that the raw material flowing into the cooling tank, inspect the body and below the hole at whether there is leakage of raw materials
3. First
2 l
Feedstock into the pot, so that the raw material flowing into the cooling tank, inspect the body and below the hole at whether there is leakage of raw materials
3. First
2 l
Feedstock into the pot, so that the raw material flowing into the cooling tank, inspect the body and below the hole at whether there is leakage of raw materials
4. Confirm leak does not exist, filling material can continue. Only when a metal probe is immersed in the pot, it shuts off until prompted
5. Press or "Auto" key to start cooling
Ice cream hardness adjustment
According to material characteristics and preferences you use to adjust the hardness of ice cream
•
On display "
H: 1.3 / 1.8
"Reaction is the hardness of ice cream
On display "
H: 1.3 / 1.8
"Reaction is the hardness of ice cream
On display "
H: 1.3 / 1.8
"Reaction is the hardness of ice cream
- -
The number before the slash is the real-time ice cream hardness
,
After setting the hardness of the slash is the number
. When the set hardness value hardness real cooling is
The number before the slash is the real-time ice cream hardness
,
After setting the hardness of the slash is the number
. When the set hardness value hardness real cooling is
The number before the slash is the real-time ice cream hardness
,
After setting the hardness of the slash is the number
. When the set hardness value hardness real cooling is
The number before the slash is the real-time ice cream hardness
,
After setting the hardness of the slash is the number
. When the set hardness value hardness real cooling is
complete, the ice cream is set larger the number the higher the hardness. When the motor is stopped stirring, the hardness of the display 0.0
- -
To adjust the hardness, according to the "Settings" button, the screen displays "hardness" tab, then press "▲" or "▼" key to adjust the hardness values, hold the adjusting After
completion of the "set" key for 3 seconds or automatically return to the wait interface to save the settings. Each adjustment amount should not exceed 0.2
- -
Ice cream hardness setting the maximum hardness, i.e. the hardness value when refrigerant is stopped, the continuous production increase can not increase the yield value
- -
Hardness settings will not lead to molding ice cream is too low, it may lead to not start cooling
- -
Even if the same set hardness, the expansion ratio also affects the state of forming the ice cream
•
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
On display "
T: -5.8_ 12.6
"Respectively
Cooling cylinder of raw materials
with
Raw material storage cylinder
Temperature, lower right
Snowflake pattern
when the lighting function is enabled show the pot precooling
, Precooling close off the snow
. Do not turn off if not necessary pre-cooling
when the lighting function is enabled show the pot precooling
, Precooling close off the snow
. Do not turn off if not necessary pre-cooling
when the lighting function is enabled show the pot precooling
, Precooling close off the snow
. Do not turn off if not necessary pre-cooling
•
Since the voltage fluctuation does not change even if the set value of the hardness, the hardness of the ice cream may also occur actual change
- -
Load values for reference, may be required under certain conditions of use is provided to compensate