background image

Every care has been taken to ensure the accuracy of the information contained in this publication, but due to continuous development  and improvement the right is reserved to supply products 

which may differ slightly from those illustrated and described in this publication.

7

www

.ceg.co

www

.ceg.co

www

.ceg.co

www

.ceg.co

www

.ceg.co

The pump should be connected to a separate circuit breaker or fuse with a minimum carrying capacity of 10A. Please note that 

if other appliances share an outlet, they may cause low voltage resulting in blown fuses, tripping of motor overload or burning 

out of the motor. A permanent earthed connection to the pump is mandatory. ECO-MXA pumps come with an earthing 

conductor and a grounding type attachment plug. Do not connect the pump to a power supply until permanently earthed. 

For maximum safety, connect pump to a circuit equipped with a Residual Current Device (RCD).

  ELECTRICAL CONNECTION

In order to ensure proper operation a static discharge head of 300mm is required; the discharge pipe must be installed 

with a vertical rise of at least 300mm!

Frost damage will not be covered under warranty!

lt is the operator’s responsibility to take all preventative measures (e.g. provision of alarm systems, standby pump etc.) To avoid 

consequential damages such as flooding due to pump failure.

300mm minimum of water above check valve

100mm minimum above bottom

Horizontal suction pipe length

Vertical suction pipe length

Drawing 2.0

   SUCTION GUIDE

Incorrect size selection of pipes may result in pump damage that is not covered under warranty and may affect pump 

performance!

2

4

6

2

4

6

8

10

Horizontal Suction Pipe Length (m)

1

8

7

5

3

32mm SP

40mm SP

12

14

16

18

20

22

24

26

9

Do not operate the pump 
in these suction conditions

40mm SP

25mm SP

SP = Suction pipe

Chart 1.0

5 - 10m

32mm

10 - 25m

40mm

0 - 5m

25mm

Horizontal Suction Installation Only

Table 3.1

Horizontal Suction 

Pipe Length (m)

Minimum Suction 

Pipe Diameter (mm)

3 - 6m

32mm

6 - 8.5m

40mm

0 - 3m

25mm

Vertical Suction Installation Only

Vertical Suction Pipe 

Length (m)

Minimum Suction 

Pipe Diameter (mm)

Suction Pipe Section Chart

Table3.0

Summary of Contents for ECO-MXA 404





















Reviews: