manualshive.com logo in svg

Cedar Summit WESTBURY F25030, Installation And Operating Instructions Manual

Share
Download
Cedar Summit WESTBURY F25030 Installation And Operating Instructions Manual Download Page 65

 

65 

[email protected]

Step 31:  Attach Belt Swings and Acro Swing

Other Parts

Fig. 31.1

Fig. 31.2

Swing Belt 

Seat

Threaded Clip

Swing 

Belt Seat

Acro Bar

Acro Handles

Threaded 

Clip

Fig. 31.3

Threaded 

Clip

A:

  Using 1 Threaded Quick Link per chain, join 1 Long Chain to each side of the Swing Belt Seat.  Make sure 

to close the Threaded Quick Link tightly using an adjustable wrench. (fig. 31.1 and 31.2).

B: 

 Using 1 Threaded Quick Link per chain, join the Short Chain to the Acro Bar.  Attach another Threaded 

Quick Link to each Acro Handle and join with first Threaded Quick Link.  Make sure to close the Threaded 

Quick Link tightly using an adjustable wrench. (fig. 31.2 and 31.3)

C:

  Attach the other end of the swing chains to the Swing Hangers.  Make sure to close the Threaded Quick 

Link tightly using an adjustable wrench. (fig. 31.1)

Caution:  Threaded Quick Links 

must be installed with the gate 

completely down covering 

the threads and tighten as 

instructed. (fig. 31.2)

Short 

Chain

Long Chain

1 x Acro Bar

2 x Acro Handle

2 x Swing Belt Seat

2 x Short Chain

4 x Long Chain

8 x Threaded Quick Link

Tighten Threaded Quick 

Link using adjustable 

wrench

Threaded Quick Links 

attach to seat and Acro 

bar.

Summary of Contents for WESTBURY F25030





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands