manualshive.com logo in svg

Cedar Summit WESTBURY F25030, Installation And Operating Instructions Manual

Share
Download
Cedar Summit WESTBURY F25030 Installation And Operating Instructions Manual Download Page 23

 

23 

[email protected]

Step 4: Fort Assembly 

Part 1

It is important to assemble the Fort Assembly on a flat, smooth surface.

A:

  Place Swing Wall from Step 3 between 2 Front/Back Walls from Step 1, noticing the wall orientations.  The 

tops and bottoms of the walls should be flush.  Make sure the walls are square then using the pilot holes as a 

guide pre-drill with a 3/16” drill bit and fasten the left Front/Back Wall to the Swing Wall and Swing Wall to the 

right Front/Back Wall with 4 (WL5) 1/4 x 2-1/2” Wafer Lags per side.  (fig. 4.1, 4.2 and 4.3)

Fig. 4.2

Fig. 4.1

Flush

Hardware

8x 

1/4 x 2-1/2” Wafer Lag

WL5

Flush

Notice left Side 

Wall overlaps 

Swing Wall

WL5

WL5

Notice Swing Wall 

overlaps Front/Back

Front/

Back Wall 

Front/

Back Wall

Swing Wall

Front/Back 

Wall

Swing Wall

Front/Back Wall

Flush

Flush

Top View

WL5

Fig. 4.3

x 4 per 

side

Notice grooves 

face inwards

Notice counter sunk 

holes on the  outside 

Left

Right

Left

Right

Summary of Contents for WESTBURY F25030





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands