manualshive.com logo in svg

Cedar Summit WESTBURY F25030, Installation And Operating Instructions Manual

Share
Download
Cedar Summit WESTBURY F25030 Installation And Operating Instructions Manual Download Page 35

 

35 

[email protected]

24 x 

#8 x 7/8” Truss Screw

A:

  In the upper opening of the Side Wall place 1 (2602) Upper Jamb so it measures 17” to the inside of each post 

then attach with 2 Jamb Mounts using 4 (S0) #8 x 7/8” Truss Screws per mount.  (fig. 11.1, 11.3, 11.4 and 11.5)

B:

  In the lower opening of the Front/Back Wall place 2 (2601) Lower Jamb so it measures 17” to the inside of each 

post then attach with 2 Jamb Mounts using 4 (S0) #8 x 7/8” Truss Screws per mount.  (fig. 11.2, 11.3, 11.4 and 11.5)

Step 11:  Install Upper and Lower Jambs

17”

17”

17”

17”

Do not cover holes 

with Jamb Mount

2602

Jamb 

Mount

S0

x 4 per 

Jamb 

Mount

Jamb 

Mount

S0

x 4 per 

Jamb 

Mount

2601

Centred

Centred

Outside View

Grooves 

to the 

inside

1 x 

Upper Jamb 1-1/4 x 3 x 35-15/16”

2 x  

Lower Jamb 1-1/4 x 3 x 41-15/16”

2602

Wood Parts

Fig. 11.1

Fig. 11.5

Hardware

2601

S0

6 x Jamb Mount

Other Parts

Inside View

Fig. 11.2

Fig. 11.3

Fig. 11.4

2602

Side Wall

Front 

Wall

2601

Front/

BackWall

Side Wall

Outside View

Summary of Contents for WESTBURY F25030





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands