manualshive.com logo in svg

Cedar Summit WESTBURY F25030, Installation And Operating Instructions Manual

Share
Download
Cedar Summit WESTBURY F25030 Installation And Operating Instructions Manual Download Page 21

 

21 

[email protected]

Step 3: Swing Wall Prep 

Part 3

It is important to assemble the frame on a flat, smooth surface.

E:

  Attach (2630) SW Top to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (WB1) 5/16 x 1” 

Wafer Bolts (with flat washer) connecting to previously installed t-nuts.  (fig. 3.5 and 3.6) 

F:

  Attach (2768) Panel Floor to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (H9) 1/4 x 1-1/4” 

Hex Bolts (with lock washer and flat washer) connecting to previously installed t-nuts.   (fig. 3.5)

G:

  Place 1 (2778) SW Ground MOD to each side of (2769) Panel BT Frame, notice the hole locations and attach 

with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer and flat washer) per board connecting to previously installed 

t-nuts.  (fig. 3.5 and 3.7)

H:

  Place 1 (2607) Diagonal under (2778) SW Ground MOD on the right hand side so the top sits against (2758) 

RT Post Assembly and loosely attach with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut).  

(fig. 3.5 and 3.7)

2 x 

5/16 x 1” Wafer Bolt (5/16” flat washer)

2 x 

1/4 x 1-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer)

3 x 

1/4 x 2-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer and 1/4” t-nut)

2 x 

SW Ground MOD 5/4 x 4 x 14-1/4”

1 x 

Diagonal 1-1/4 x 3 x 22”

H9

Wood Parts

Hardware

2778

Fig. 3.6

Fig. 3.5

2758

2757

Note which bolt holes are used

x 2

2607

2630

2768

WB1

2607

H9

x 3

WB1

WB1

2778

2778

2769

2769

2778

2778

Fig. 3.7

x 2

FW1

LW1

FW2

TN1

H10

H10

Summary of Contents for WESTBURY F25030





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands